C0045: rear left wheel sensor
Left Rear Wheel Speed Sensor Circuit
Severity: high
Updated: 18 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the ABS brake ECU, or the unit that manages stability control, has detected an electrical fault or an inconsistent signal from the left rear wheel speed sensor. Each wheel has a sensor that reads the passing of the teeth of a tone ring, which turns with the hub, and from that reading the ECU calculates the speed of each wheel and compares them with one another. If the circuit is open, short-circuited or if the signal does not arrive normally, the ECU cannot reliably know what that wheel is doing. For safety, it deactivates the ABS control and, on many vehicles, also the stability and traction control, while the conventional brake continues to work.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got C0045? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
How the ECU detects it
The ECU continuously monitors the signal from each sensor. As soon as it detects an open circuit, a short circuit or an impossible reading for a set period, it stores the code and lights the warning light. Some faults only appear once a certain speed is reached, which is why the light may come on while driving and not when starting from standstill. If the loss of signal is intermittent, the code may disappear and be stored again after several driving cycles.
Symptoms
- The ABS warning light comes on, and often also the stability or traction control light.
- On some vehicles, a message appears in the instrument cluster about the braking or stability system.
- When braking hard, the characteristic ABS vibration is not felt, although the pedal still works.
- The fault may appear only above a certain speed, or only in bends or on wet roads.
- In some cases the light flashes or goes off and comes back on intermittently.
Common causes
- Sensor cable or connector damaged by chafing, stone impacts, moisture or corrosion. This is often one of the most frequent causes, although it depends on the vehicle.
- Faulty speed sensor or with a distorted signal.
- Dirty tone ring, with metal adhered, with damaged teeth or with play in the wheel hub.
- Excessive gap between the sensor and the ring, due to incorrect fitting or a worn bearing with play.
- Internal fault in the ECU, which is the least likely possibility.
What to check
- With the ignition on, observe which warning lights come on and whether the ABS light goes off after a few seconds. Note whether any other code appears at the same time, as it changes the diagnosis.
- Visually inspect the left rear sensor cable, from the sensor itself to where the cable joins the rest of the harness. Look for chafing, cuts, loose clips, traces of mud or heat damage. If you need to raise the car to see it, use approved axle stands and chock the opposite wheels. Never work under a vehicle supported only by a jack.
- Check that the connector is properly seated, free of rust, without water inside and with no broken locks. A loose connector is a very common cause.
- Carefully clean the tip of the sensor and the visible area of the ring with a dry cloth or a soft brush. Do not use metal tools or scrape the ring.
- Read the codes with an OBD-II reader to confirm that the fault is in the left rear sensor and that there are no associated ones. Clear the code only after noting it down, and watch whether it reappears after a few kilometres.
- Ask a garage for the full check: sensor resistance, signal waveform with an oscilloscope, condition of the tone ring and play in the wheel hub. These tests require specific equipment and knowledge.
- Important: do not dismantle or tamper with the brakes, the caliper, the disc, the ABS or the wheel hub to carry out tests yourself. A mistake with these components can cause serious injury. Diagnosis and repair should be carried out by a garage.
Common diagnostic mistakes
- Clearing the code and considering the problem solved without checking the cause, so it reappears.
- Replacing the sensor without first checking the cable and connector, which are usually the real source of the fault.
- Confusing this code with that of another wheel through a hasty reading of the report.
- Cleaning the tone ring with metal objects or scraping it, which can damage the teeth.
- Assuming the car brakes the same as with ABS active and not adjusting driving while the system is deactivated.
- Trying to tamper with the braking system or the wheel hub without tools or training, with a risk of injury.
Typical repairs
From the simplest and cheapest to the most expensive. Which one applies depends on the diagnosis.
- Clean the sensor, the visible ring and the connector.
- Retighten or reseat the connector and secure the cable with its original clips.
- Repair a damaged cable with correct splices and adequate protection, at a garage.
- Replace the left rear wheel speed sensor, correctly setting its gap to the ring.
- Replace the tone ring or the wheel hub with bearing, at a garage with suitable tools.
- Replace the ABS ECU only when the other checks have ruled out the remaining causes.
Frequently asked questions
Can I keep driving with the ABS light on because of the left rear sensor?
You can continue driving with caution until you reach the garage, because the conventional brake still works, but without ABS or stability control. Avoid sudden braking, especially on wet roads, gravel or in bends, and leave more distance from the vehicle in front. Do not drive if the brake warning light also comes on, the pedal becomes soft or abnormally hard, you notice loss of brake fluid or the car pulls to one side when braking. In that case, do not drive and call for roadside assistance. Take the car to be checked soon, without delay.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
Related codes
- C0035 Corresponds to the front left wheel sensor, not the rear.
- C0040 Corresponds to the front right wheel sensor.
- C0050 Corresponds to the rear right wheel sensor, the opposite side.
- C0110 Indicates a fault in the ABS pump motor, not in a wheel sensor.