P0500: Vehicle Speed Sensor Malfunction
Severity: medium
Updated: 18 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
The engine control module (ECM/PCM) needs to know the vehicle speed to regulate ignition, fuel injection, cruise control, automatic gearbox shifts and other systems. That information comes from a speed sensor, located depending on the model in the gearbox, in the differential or by using the signals from the wheel sensors. Code P0500 is set when the ECU receives no speed signal or receives a signal that does not match the rest of the data, for example when the engine is turning and the vehicle is moving but the sensor reports no movement. If the fault persists, the ECU stores it in memory and may activate protective measures.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0500? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Speedometer that reads zero, swings erratically or does not respond
- Odometer stopped or showing inconsistent readings
- Cruise control or speed limiter that does not work
- Jerky, delayed or missing gear changes in the automatic gearbox
- Limp mode with restricted speed or reduced throttle response
- ABS, ESP or stability control warning lights on, depending on the model and whether those control units use the same speed signal
- Slightly higher (≈) fuel consumption due to less precise engine management
Common causes
- Damaged, dirty or metal-debris-covered speed sensor
- Broken, cut or corroded sensor wiring or connector
- Damaged, worn or misaligned tone ring or signal gear
- Poor earth or power supply to the sensor
- Fault in the ECU or in communication between control units (less common)
- Causes specific to the make and model, such as sensor location or whether the signal travels over the CAN network
What to check
- Read the live speed data with a scanner and compare it with the speedometer or with a GPS on the road
- Visually inspect the connector, wiring and sensor area for damage, moisture or corrosion
- Clean the sensor and check that it is securely fitted and at the correct distance from the tone ring or gear
- Check the tone ring or signal gear for broken teeth or wear
- Measure the sensor's resistance, voltage or signal with a multimeter or oscilloscope, according to the manufacturer's values
- Check the power supply and earth of the sensor and the ECU
- Verify communication with other control units, such as ABS or gearbox, to rule out a network fault
- Safety: if the vehicle must be raised to access the sensor, use proper supports or a lift; never work under a car held up only by a jack. If the sensor is next to brake components, do not dismantle the brakes without training; if in doubt, go to a garage
Frequently asked questions
Can I keep driving with code P0500 active?
It depends on the symptoms. If only the speedometer is faulty and there are no other warnings, you can drive for the short term with care, knowing the actual speed is unknown, and it is best to have it checked soon. If the ABS or ESP warning light comes on, braking on wet roads or in corners may be less stable: drive with more margin, avoid harsh braking on slippery tarmac and go to a garage as soon as possible. If the car goes into limp mode, the gear changes are jerky or the gearbox is not engaging gears, avoid long journeys and have it looked at; if it is not safe to continue, call for a tow. If you notice the brakes responding differently or other faults appear, do not drive it and consult a professional.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.