Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0097: intake air temp 2 low

Intake Air Temperature Sensor 2 Circuit Low

Severity: medium

Updated: 16 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code indicates that the ECU (PCM) reads a voltage below the expected range on the circuit of the second intake air temperature sensor (IAT2). As the sensor is a resistor that varies with temperature, a voltage that is too low is interpreted as excessively hot air or, directly, as a short to earth or an internal sensor fault. The ECU cannot rely on that reading and replaces it with a safety value or discards it. The IAT2 sensor only exists on some engines and its location varies: it may be in the intake manifold, in a section after the intercooler or built into the mass air flow meter. That is why it is worth confirming in the vehicle handbook which sensor corresponds to this number before touching anything.

Can I keep driving?

Yes, but have it checked soon.

The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0097? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

How the ECU detects it

The ECU continuously monitors the voltage of the IAT2 circuit while the engine is running and, on many vehicles, also with the ignition on. The fault is recorded when the voltage remains below the minimum threshold for a set period of time. Such a low voltage usually indicates a short to earth or contact with another wire in the circuit; an open sensor, by contrast, produces a high reading (see P0098). That is why the code may appear immediately on cold start or only after several driving cycles. If the condition disappears, the warning light may go off, although the code stays stored.

Symptoms

  • In many cases nothing is noticeable while driving, because the ECU uses an estimated temperature.
  • There may be a slight increase in fuel consumption or a slightly richer running in some conditions, especially with the engine warm.
  • If the sensor is part of the mass air flow meter, on some designs there may be jerking, uneven idling or difficulty starting from cold.
  • The warning light may stay on constantly or come on and go off depending on engine temperature.
  • Occasionally other codes related to the intake or the mixture appear, which means the whole system needs checking.

Common causes

  • IAT2 sensor internally damaged or with its resistance altered by heat or moisture.
  • Cable or connector with a break that causes a short to earth on the signal or on the reference supply.
  • Corroded connector, poorly seated or with moisture build-up in the sensor housing.
  • Short between the signal wire and another wire in the same harness, through chafing or a badly made splice.
  • Fault in the ECU itself, which is uncommon and is only confirmed once the other components have been ruled out.
  • Sensor built into the mass air flow meter that has failed due to contamination with oil or dirt, on designs where this happens.

What to check

  • Consult the handbook or the wiring diagram to locate the IAT2 sensor and its exact connector.
  • Visually inspect the connector and wiring: look for moisture, corrosion, bent pins, damaged insulation and cables crushed by some component.
  • With the ignition on and the engine cold, read the IAT2 temperature value with a scanner and compare it with IAT1 and with the ambient temperature. If the value is very high or does not change, a fault is suspected.
  • Disconnect the sensor and measure its resistance with a multimeter at ambient temperature. Compare the value with the manufacturer's tables or with the actual air temperature.
  • Measure the reference voltage at the connector with the ignition on and check that it is present and that the signal is not shorted to earth, using the vehicle diagram.
  • Check the continuity of the wires between the connector and the ECU, and the absence of shorts to earth and between wires.
  • If all of the above is correct, check the ECU or the integrated mass air flow meter, always with the manufacturer's data at hand.

Common diagnostic mistakes

  • Replacing the sensor without first checking the wiring and connector, when the fault is usually in the connection.
  • Confusing the IAT1 sensor with IAT2 and checking the wrong component.
  • Clearing the code and considering the car repaired without verifying that the temperature reading is correct after several driving cycles.
  • Measuring the sensor's resistance when hot or with the connector poorly disconnected, obtaining misleading values.
  • Ignoring the possibility that the sensor forms part of the mass air flow meter and replacing only a partial component.
  • Assuming that a temperature code means an ECU fault without having first ruled out external components.

Typical repairs

From the simplest and cheapest to the most expensive. Which one applies depends on the diagnosis.

  • Clean the connector contacts and apply an electrical protective product if there is corrosion.
  • Repair a damaged cable or a faulty splice, using soldering or a suitable terminal with heat-shrink protection.
  • Replace the complete connector when pins are deformed or the housing is broken.
  • Replace the IAT2 sensor with an original or good-quality equivalent, after confirming the fault with measurements.
  • Replace the mass air flow meter when the IAT2 sensor is integrated and the assembly has failed.
  • Reprogram or replace the ECU only as a last resort, after ruling out all other components.

Frequently asked questions

Can P0097 affect power or fuel consumption?

In most cases the loss of performance is small or unnoticeable, because the ECU replaces the failed reading with an estimated value, and it normally does not prevent driving. A slight increase in fuel consumption or slightly irregular running when cold may be noticed, especially if the sensor is built into the mass air flow meter. Even so, it is best to have it checked soon, as a badly calculated intake temperature can affect the mixture adjustment.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

Related codes

  • P0095 Indicates a generic fault in the IAT2 sensor circuit, without specifying whether the reading is low or high.
  • P0098 It is the same IAT2 sensor, but with the voltage above the range, which usually indicates an open circuit.
  • P0112 Affects the IAT1 sensor, the first in the system, so it is best not to confuse the two sensors.
  • P0102 Refers to the mass air flow meter with a low signal, which on some designs shares a housing with the IAT2.

More codes: fuel, air metering and emission controls

All OBD codes in English