P0093: Fuel System Leak Detected (Large Leak)
Severity: high
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the ECU (ECM or PCM) has detected a major leak in the fuel or evaporative emissions (EVAP) system. To check this, the system carries out tightness tests by applying controlled pressure or vacuum and monitoring its drop using pressure sensors. A loss that exceeds the programmed threshold triggers the code. Depending on the manufacturer, the test may run with the engine off, after the vehicle has been switched off, or during a specific driving cycle. As the diagnosis is based on pressure differences measured by the ECU, the actual leak may be in the vapour circuit, the tank or the fuel supply line, so it has to be located physically.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0093? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Check engine warning light on. In many cases it is the only symptom.
- Smell of petrol, especially when parked or after refuelling, if the leak is noticeable.
- Stains or dripping of fuel under the vehicle, only with visible leaks.
- Fuel level dropping faster than usual, if the leak is real.
- Difficulty starting or loss of power only if the leak affects supply pressure, which is uncommon with this code.
Common causes
- Fuel cap damaged, not closed properly or with a deteriorated seal.
- Hoses or pipes in the vapour circuit cracked or disconnected.
- Fuel tank filler neck cracked or corroded.
- Tank purge or vent valve leaking.
- Fitting, connection or supply line leaking.
- Fuel pressure regulator diaphragm deteriorated, which can be a cause on some engines.
- Leak in the tank itself (uncommon case).
- Note: the layout of components varies greatly between makes and engines, so the most likely cause depends on the model and year. Check the manufacturer's technical information.
What to check
- Before touching any fuel component: do not smoke, do not use flames or tools that can produce sparks, work in a ventilated area and depressurise the circuit according to the manufacturer's procedure.
- Check that the cap is properly closed and that its seal is not damaged or dirty.
- Visually inspect the filler neck, hoses and pipes for cracks, chafing or disconnections.
- Check visually for fuel stains under the vehicle. The sense of smell only serves as an indication, not as a measurement.
- Read the additional codes and the freeze frame data to see under what conditions the fault appeared.
- Check the connections and the condition of the tank purge and vent valves.
- Carry out a smoke test on the vapour circuit to locate the leak precisely, at a garage with the proper equipment.
- Measure the fuel system pressure and the tightness of the supply circuit, only if you have the equipment and training. Repairs to the supply line should be carried out by professionals.
- Inspect the tank and the pressure regulator if the previous tests do not locate the leak.
Frequently asked questions
Can I keep driving with P0093 on?
It depends on the symptoms. If the warning light is on without smell, dripping, and the engine runs normally, you can usually drive with caution to a garage to diagnose the leak. If you notice a strong smell of petrol, especially inside the cabin or under the bonnet, see fuel dripping under the car, or the engine starts with difficulty, stop the engine, move away from the vehicle, do not smoke, and call for a tow truck. A badly closed cap is the simplest cause to check, but you should not assume it is the only possible origin.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.