P0141: Heated Oxygen Sensor Circuit Bank 1 Sensor 2
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
Code P0141 means the ECU has detected a fault in the heater circuit of the oxygen sensor fitted after the catalytic converter, on bank 1. This sensor has an internal heating element that warms it up so it reaches its working temperature more quickly. The ECU monitors the voltage or current in that circuit and compares what it receives with the expected values during start-up and running. If the reading is out of range or the sensor does not respond to heating, it stores the code and usually lights the warning lamp. The rear sensor does not regulate the mixture in real time like the front one, so the fault rarely affects driving straight away.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0141? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Warning lamp (MIL) on, usually steady.
- Often there are no noticeable symptoms when driving.
- Possibly slightly higher fuel consumption, although it is usually hard to notice and depends on the vehicle.
- On some vehicles, the ECU may not complete the catalytic converter diagnostic cycles.
- If the fault is intermittent, the code may come and go with temperature or vibration.
Common causes
- Rear oxygen sensor (sensor 2) with a burnt-out or worn heater. This is one of the most common causes as the vehicle gets older.
- Heater circuit wiring damaged by rubbing, heat or moisture.
- Sensor connector corroded, loose or with bent pins.
- Faulty fuse or relay for the oxygen sensor heaters.
- Poor connection on the circuit's earth or power supply.
- A rare fault in the ECU itself or its control stage, which is usually ruled out before the causes above.
- Depending on the make and engine, the circuit may share a fuse or relay with other systems, which changes how the fault is traced. It is worth checking the wiring diagram for the specific vehicle.
What to check
- Read the code with an OBD-II reader and check whether there are other sensor or catalytic converter codes.
- Work with the exhaust cold: the sensor and exhaust pipe can burn you. Wait for them to cool before touching them.
- Visually inspect the rear sensor connector and the wiring near the exhaust, looking for damage, corrosion or moisture.
- Check the oxygen sensor heater fuse and relay against the vehicle's wiring diagram.
- Measure the resistance of the sensor heater between its power pins, comparing it with the manufacturer's reference value. Disconnect the sensor carefully, without pulling the cable or forcing the connector.
- Check the power supply and earth of the circuit at the connector with the ignition on, using a multimeter and without short-circuiting pins.
- Check the continuity of the wiring between the connector and the ECU.
- If all of the above is correct, assess the sensor with an oscilloscope or live data, or consult a specialist garage.
Frequently asked questions
Can I keep driving with code P0141 if the car runs fine?
In most cases yes, because the rear sensor does not control the fuel mixture in real time and the engine keeps running normally. Even so, it is best to have it checked soon to stop the fault affecting catalytic converter management or other diagnostics. If you notice a loss of power, clearly higher fuel consumption or a strong smell of petrol, it is better to go to a garage sooner.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: fuel and air metering
- P0113 · Intake Air Temperature Circuit High Input
- P0122 · throttle sensor low
- P0128 · Engine Coolant Temperature Below Thermostat Regulating Temperature
- P0133 · Oxygen (Lambda) Sensor Circuit Slow Response, Bank 1 Sensor 1
- P0135 · Heated Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
- P0171 · System too lean (Bank 1)
- P0172 · Fuel System Too Rich (Bank 1)
- P0174 · System Too Lean (Bank 2)