Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0135: Heated Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)

Severity: medium

Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code indicates that the ECU has detected a fault in the circuit that powers the heating element of the oxygen sensor (lambda sensor) located before the catalytic converter, on bank 1 (the bank containing cylinder number 1). This heater brings the sensor up to its working temperature, of around ≈300 °C, so that it produces a useful signal a few seconds after starting. The ECU monitors the current or voltage in the circuit and compares the measured values with the expected ranges. If the circuit appears open, short-circuited or out of range for a set period of time, it stores the code. While the sensor is not hot, its reading is not reliable and the ECU cannot use it to adjust the mixture.

Can I keep driving?

Yes, but have it checked soon.

The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0135? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Check engine warning light constantly on. This code does not usually make the light flash.
  • On some vehicles, slightly unstable idle during the first few minutes after a cold start; on others, nothing noticeable while driving.
  • Possible slight increase in fuel consumption, more noticeable on short journeys.
  • Sometimes there are no driving symptoms at all; the fault is only detected when reading the codes from the ECU.

Common causes

  • Faulty sensor heating element, one of the most common causes, especially as the vehicle ages.
  • Heater wiring broken, chafed or damaged, especially near the exhaust because of the heat.
  • Sensor connector with corrosion, moisture, or bent or loose pins.
  • Faulty heater power fuse or relay. On some models the relay is shared with other circuits; this depends on the manufacturer and the vehicle.
  • Fault in the ECU control circuit, uncommon and generally the last thing to rule out.

What to check

  • With the engine off and cold, visually inspect the sensor connector and wiring, looking for corrosion, burnt cables or broken insulation. The exhaust area can be very hot and cause burns.
  • Check the heater fuses and relays according to the manufacturer's diagram.
  • With the ignition on, check the supply voltage at the sensor connector, following the vehicle's wiring diagram. Work carefully to avoid short circuits.
  • Measure the heater resistance with a multimeter between its pins, with the connector disconnected; the reference value depends on the manufacturer and should be checked in the technical documentation.
  • Check continuity of the wiring between the sensor connector and the ECU, with the vehicle off and the connector disconnected.
  • Read live data of the sensor heater status with a scanner, to see whether the ECU records the fault continuously or intermittently.
  • If all of the above is correct, check the ECU control output. This task requires specialist equipment and knowledge; it is best left to a garage.
  • If the work involves touching the exhaust, wait until it has cooled down completely.

Frequently asked questions

Why can fuel consumption rise when the P0135 appears?

Without a reliable signal from the sensor once it is hot, the ECU cannot accurately correct the air-fuel mixture. In that case it usually uses default values that tend to enrich the mixture, which can slightly increase fuel consumption, especially on short journeys and with a cold engine. The effect is not the same on every vehicle and is not always noticeable when driving. The fault is not usually dangerous in the short term, but it should be checked soon because consumption and emissions can worsen over time.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: fuel and air metering

All OBD codes in English