P0606: Processor Fault in Engine Control Module (ECM/PCM)
Severity: high
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
Code P0606 means the engine control module (ECM or PCM) has detected a fault in its own processor or in its internal control circuit. The ECU runs a self-test program when it is switched on and during operation, and this code is stored when those checks fail or when the microprocessor does not respond as it should. It does not necessarily mean the ECU is permanently faulty, as the fault is sometimes caused by an unstable power supply or a one-off electrical interference. As the fault affects the brain of the system, the vehicle's response can become unpredictable.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0606? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Malfunction indicator lamp (MIL) on, either steady or flashing.
- Engine cutting out suddenly, sometimes without warning.
- Difficulty starting, or intermittent starting.
- Irregular idle or revs rising and falling for no reason.
- Limp mode, with loss of power and limited speed.
- Faults in other electronic systems, such as automatic gearbox, traction control or lights, depending on the model.
- Erratic behaviour of the instruments on the dashboard.
Common causes
- Power or earth fault in the ECU: low battery voltage, loose or corroded connections on the power supply or earth.
- Charging system problems, such as an alternator that does not maintain the correct voltage, which can damage the electronics.
- Internal fault in the processor or electronic components of the ECU itself.
- Corrupted software or calibration, which on some makes is fixed by a reprogramming from the manufacturer.
- Damage from moisture, overheating or knocks to the ECU or its connector.
- Electrical interference from poorly fitted accessories, depending on the vehicle.
What to check
- Check the battery voltage with the engine off: it should be around ≈12.6 V at rest. During cranking the voltage drops temporarily; with the engine running it should settle at around ≈13.5–14.5 V (indicative values, which vary by manufacturer).
- Visually inspect the battery earths and terminals, looking for corrosion, loose or broken cables. Before touching the terminals, switch off the ignition. The battery contains acid and can give off flammable gas, so its terminals must not be short-circuited.
- Read the stored faults and the freeze frame data to see under what conditions the code appeared.
- Check for other power or communication (CAN) codes, which usually appear alongside P0606.
- Check the charging system by measuring the voltage with the engine running and with electrical loads connected.
- Consult manufacturer technical service bulletins (TSB) or software updates for the specific model.
- Inspect the ECU connectors, looking for moisture, bent pins or corrosion.
- Only after ruling out power, earths and communication should you consider replacing or reprogramming the ECU, as it is the most expensive repair. These tasks should be carried out by qualified technicians.
Frequently asked questions
Can I keep driving with code P0606 showing?
Continuing to drive normally is not recommended. The ECU controls fuel injection and ignition; if it fails, the engine may stall without warning, which is dangerous in traffic. On some vehicles, stopping the engine also removes brake or steering assistance. If the engine stalls or goes into limp mode, you should not drive. If the engine runs normally, take the vehicle to a garage as soon as possible and avoid long journeys. Diagnosis should be carried out by a professional.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.