P0670: Glow Plug Module Control Circuit
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code means the engine ECU detects a fault in the circuit that controls the glow plug module, the component that manages the warm-up time of the glow plugs before starting. It is a code associated with diesel engines, which use these glow plugs to make cold starting easier. The ECU monitors the control signal and the electrical response of the module, and if those signals do not match what the ECU commands, it stores the code and may switch on a warning light. The problem mainly affects starts with a cold engine.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0670? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Starting the engine is harder, especially in low temperatures.
- Uneven idle or white smoke during the first minutes after starting.
- Glow plug warning light that flashes, stays on or does not go off.
- In some cases, the engine starts well when warm and only fails when cold.
Common causes
- Faulty glow plug fuse or relay.
- Damaged wiring, with chafing, corrosion or loose connectors in the control circuit.
- Faulty glow plug control module.
- A glow plug that is short-circuited or open, which may cause the ECU to detect a circuit fault.
- Poor earth or power supply to the module.
- The exact cause depends on the make and model, because the module location, the number of glow plugs and the type of connection vary between manufacturers.
What to check
- Check the glow plug fuse and relay, as this is the simplest check.
- Visually inspect the circuit's wires and connectors, looking for damage, moisture or corrosion.
- Check the module's supply voltage and earth with a multimeter.
- Check the resistance of each glow plug and compare the values with each other.
- Consult the manufacturer's data for the reference values and the specific wiring diagram for the vehicle.
- If all of the above is correct, replace the control module, first checking that there are no faults in the engine ECU.
Frequently asked questions
Why is the engine harder to start when cold with P0670?
The glow plugs heat the combustion chamber before starting, and without that help the diesel mixture is harder to ignite in low temperatures. If the module that controls them fails, the glow plugs may not receive the power or the warm-up time they need. That is why the problem usually shows only when cold and goes away once the engine is warm.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.