Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

U0100: Loss of Communication with ECM/PCM "A"

Severity: high

Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code indicates that a module on the vehicle network has stopped receiving the expected messages from the engine control module, identified as ECM/PCM "A". The letter "A" denotes the main module when there is more than one control unit of that type. Each control unit sends periodic messages over the CAN network, and if one of them receives no response or data from the ECM/PCM within a time interval defined by the manufacturer, it records U0100. The fault may lie in the ECM/PCM itself, in the network wiring or connectors, or in the power supply of one of the modules. Depending on each vehicle's strategy, the control unit that detects the loss may activate an emergency operating mode.

Can I keep driving?

Only as far as you need to, and gently.

This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got U0100? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Warning or engine light illuminated on the instrument cluster.
  • Error messages on the cluster relating to the engine, transmission or driver assistance systems.
  • Loss of power or limited operation (emergency mode).
  • Rough idle, engine stalling or difficulty starting in severe cases.
  • Failure of auxiliary electronic systems, such as climate control, central locking or stability control, which depend on the network.
  • Some symptoms may appear only with vibration, humidity or when the wiring harness is moved, which points to an intermittent contact.

Common causes

  • ECM/PCM connector loose, corroded or with damaged pins.
  • Communication network wiring damaged, cut or short-circuited between wires.
  • ECM/PCM power supply or earth faulty, due to a fuse, relay or defective connection.
  • CAN network termination resistors in poor condition or disconnected. The network configuration varies by make.
  • ECM/PCM internally faulty.
  • Software in some module out of date or incompatible after a repair. This depends on the manufacturer and model.
  • Module from another network connected incorrectly or faulty, blocking the bus (less common).

What to check

  • Before disconnecting connectors or measuring on the modules, consult the manufacturer's procedure. On vehicles with airbags or high-voltage systems (hybrids and electric vehicles), follow the specific safety instructions and do not touch orange cables or high-voltage components without proper training.
  • Visually inspect the connectors of the ECM/PCM and nearby modules, looking for moisture, corrosion or bent pins.
  • Measure battery voltage and the condition of the main earths, as low voltage can cause erratic communication.
  • Check the fuses and relays supplying the ECM/PCM according to the manufacturer's diagram.
  • Read all network codes, not just U0100. If several U codes appear, the problem is usually common to several modules.
  • With the ignition off and the battery in normal condition, measure the resistance between CAN-H and CAN-L. In a high-speed CAN network (ISO 11898) with two 120 Ω terminations in parallel it should be around ≈60 Ω. Confirm your network's configuration in the manufacturer's documentation, as it varies by make and model. Values far from this point to a damaged resistor or a short circuit.
  • Move the wiring harness with the engine running and observe whether the fault appears or disappears. Only do this if you can do it safely.
  • Measure the network signal with an oscilloscope or CAN analyser to see whether the ECM/PCM messages arrive correctly.
  • Verify the software version of the modules and, if appropriate, update it using the manufacturer's technical information and official tools.
  • If all of the above is correct, suspect the ECM/PCM and replace or repair it only after confirming the fault.

Frequently asked questions

Can I keep driving with U0100 active?

It depends on the symptoms. If the engine runs normally and no other warnings appear, take the car to a garage soon, as the fault may get worse. If the engine stalls, will not start, loses power, enters an emergency mode, or the warnings for brakes, power steering, ABS, airbag or stability control light up, do not drive: call for a tow. If the engine stalls while moving, switch on the hazard lights and carefully leave the carriageway. Do not attempt to repair the fault at the roadside.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: network and communication

All OBD codes in English