U0140: Loss of Communication with Body Control Module (BCM)
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the engine ECU or another main module has stopped receiving valid messages from the body control module (BCM). The BCM manages functions such as the lights, central locking, wipers, windows and, on many vehicles, the anti-theft or immobiliser system. The ECU detects the fault when it does not receive the expected frames on the vehicle's communication network, normally a CAN network, for a set period of time. As the message does not arrive, the system stores the code and may activate safety or fallback functions.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got U0140? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Warning or fault light on in the instrument cluster.
- Body functions not responding: lights, central locking, electric windows or wipers.
- Error messages in the cluster about electronic systems.
- On some vehicles, difficulty starting or the immobiliser warning.
- Intermittent faults that come and go depending on temperature or vibration.
Common causes
- Faulty BCM power supply or earth, due to blown fuses, worn relays or loose connections.
- Damaged communication network wiring, with a short circuit, open circuit or chafing, especially at body panel passages and connectors.
- Corroded or rusted network connectors, often caused by moisture.
- BCM module internally faulty.
- Another module on the network that is faulty and brings down communication with the rest.
- The location of the BCM, the connector names and the network structure vary by make and model, so it is worth consulting the manufacturer's wiring diagram.
What to check
- Check the fuses and relays that power the BCM according to the vehicle handbook.
- Check the battery: at rest it should be around ≈12.6 V, and a low voltage can cause erratic communication.
- Visually inspect the BCM connectors and earths, looking for corrosion, moisture or bent pins.
- Read all the vehicle's codes with a scanner, including those from other modules. If there are several U codes at once, the problem is usually in the network.
- Measure the CAN network termination resistance with the ignition off. On many high-speed networks it is around ≈60 Ω between CAN-H and CAN-L; the exact value depends on the vehicle.
- Check the CAN network wiring section by section, looking for breaks, chafing or poor splices.
- Use an oscilloscope to observe the signal on the CAN bus and detect short circuits or interference.
- Replace or reprogram the BCM only as a last step, once the causes above have been ruled out.
Frequently asked questions
Can I keep driving with code U0140?
It depends on the symptoms and there is no single answer. If the vehicle starts normally, the dipped beams, brake lights and indicators work, the wipers respond and no brake, steering or airbag warning is lit, you can drive with caution to a garage to have it checked. Do not drive if the car will not start, if the lights, wipers or indicators fail, if any brake, steering or airbag warning comes on, or if the anti-theft system prevents starting. In those cases do not drive: call a recovery service or a professional, as the fault can suddenly get worse.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: network and communication
- U0100 · Loss of Communication with ECM/PCM "A"
- U0101 · Loss of Communication with Transmission Control Module (TCM)
- U0107 · throttle no comms
- U0121 · Loss of Communication with Anti-Lock Brake System (ABS) Control Module
- U0155 · Loss of Communication with Instrument Panel Cluster (IPC) Control Module