P0715: Input/Turbine Speed Sensor Circuit Malfunction
Severity: medium
Updated: 14 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
Code P0715 means the ECU detects an incoherent or missing electrical signal in the circuit of the transmission input speed sensor, also called the turbine sensor. This sensor measures the rotational speed of the shaft entering the gearbox, that is, the one that receives the rotation from the torque converter or the clutch. The ECU compares that reading with other signals, such as output speed or engine speed, and if they do not match or the signal is missing altogether, it stores the code. On many vehicles, the gearbox then switches to a safety mode with fixed gears. Which module manages the transmission depends on the manufacturer.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0715? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Harsh or delayed gear changes, especially when moving from one gear to another.
- Fixed gear or emergency mode, with reduced power.
- Warning light or gearbox light lit on the instrument cluster.
- Erratic or zero turbine speed reading during diagnosis.
- Jerking on acceleration or torque converter slip.
Common causes
- Faulty input speed or turbine sensor.
- Damaged connector or wiring harness, with corrosion or loose contacts.
- Dirty tone wheel or sensor magnet, with metal filings or wear.
- Low level or contaminated transmission fluid, which can alter the reading.
- Transmission control module fault, a less common cause.
What to check
- Check the gearbox fluid level and condition, with the engine at the temperature specified by the manufacturer. The procedure depends on the manufacturer. Hot fluid can cause burns.
- Visually inspect the sensor connector and the harness that follows it.
- Clean the connector and check that it is firmly fitted.
- Read the live data of the input speed sensor with a scanner and compare it with engine speed.
- Measure the sensor's continuity and power supply with a multimeter, with the ignition off for continuity, following the manufacturer's wiring diagram.
- Check the sensor signal waveform with an oscilloscope.
- Test the transmission control module only after ruling out the above.
Frequently asked questions
Can I keep driving with P0715 if the car seems to be running fine?
It depends on how the gearbox behaves. If the gear changes are smooth, there is no emergency mode and the car does not lose power, you can drive carefully and have it checked soon. If the gearbox gets stuck in a fixed gear, jerks or reduces power, do not keep driving, especially on motorways or when overtaking, because you could lose power at a dangerous moment. Take it to a garage. Leaving the fault unresolved may contribute to wear on the torque converter or clutches over time.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.