P0740: Torque Converter Clutch (TCC) Circuit Malfunction
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
P0740 is a generic code (SAE J2012 / ISO 15031-6) that indicates a fault in the electrical control circuit of the torque converter clutch (TCC). The ECU detects the TCC solenoid or control valve as open, short-circuited or with values outside the expected range. This clutch locks the converter so that the engine and gearbox turn directly at cruising speed, which improves performance and reduces fuel consumption. If the circuit fails, the lock-up may not engage. As the code describes an electrical problem, it does not by itself indicate which part has failed, so it is worth checking the circuit before replacing components. Some manufacturers also use P0740 for mechanical TCC faults; in that case, check the manufacturer's definition.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0740? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Engine warning light on
- Loss of converter lock-up: engine speed rises at constant speed
- Higher fuel consumption on the motorway
- Slight vibration or jerking at cruising speed
- Feeling of slipping, or the gearbox seems slow to change
- In some cases, limp mode with slower response
Common causes
- Faulty TCC clutch solenoid or altered resistance
- Solenoid connector or harness damaged, corroded or with poor contact
- Short to earth or to positive, or open circuit between the ECU and the solenoid
- Valve body with the control valve stuck or contaminated by particles
- Transmission fluid degraded, dirty or at the wrong level (in gearboxes where it can be checked)
- Fault in the transmission or engine ECU, or outdated software
- Depending on the make, the ECU that controls the TCC may be the gearbox one or the engine one, which changes where to look
What to check
- Check the warning light and note whether the code is permanent or intermittent
- Read all stored codes, including related ones (such as P0741), to tell an electrical fault from a performance one
- Visually inspect the TCC solenoid connector and harness for damage or corrosion
- Check the fluid level and condition, if the manufacturer allows it, and see whether it smells burnt
- Use a scanner to read live data: TCC status, converter slip and lock-up commands
- Measure the solenoid resistance and compare it with the manufacturer's values (≈ varies widely by model)
- Check technical bulletins and ECU software updates
- If all of the above is correct, inspect the valve body and the TCC control valve; this work involves removing the transmission and should be done by a professional
- If the vehicle must be raised, use an approved lift or axle stands, never only a jack, and work with the engine off and the exhaust cold
Frequently asked questions
Can I keep driving with P0740 if I don't notice anything wrong?
On many vehicles it is possible to drive in the short term, because the ECU usually disables converter lock-up and the gearbox works without it. Even so, it is not a fault to ignore: without lock-up, the converter can heat the transmission fluid. Avoid towing loads and long high-speed journeys. Stop the vehicle and consult a professional if the warning light flashes, if a transmission temperature warning appears, if you notice jerking or slipping, or if fuel consumption rises abnormally.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.