P0730: Incorrect Gear Ratio
Severity: high
Updated: 14 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
Code P0730 indicates that the transmission ECU has detected that the ratio between input speed and output speed does not match the gear currently selected. To check this, it compares the readings from the input and output speed sensors with the theoretical ratio for each gear. If the difference stays outside the programmed limits for a certain time, it stores the code and, in many cases, lights the warning lamp. It usually appears when the gearbox slips in one gear, when the clutch or the bands of an automatic do not hold properly, or when there is an electrical or hydraulic fault that prevents the correct gear ratio from being engaged. The code describes the symptom, not the specific failing part, so a diagnosis is needed to find the cause.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0730? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Slipping, or engine revs rising without a proportional increase in speed.
- Abrupt, delayed or incomplete gear changes.
- Stuck gear, for example the car staying in second or going into limp mode.
- Jerking or loss of power when accelerating.
- Smell of burning or rising temperature of the gearbox oil.
- Warning or transmission light on in the instrument cluster.
Common causes
- Low transmission fluid level or degraded fluid, with loss of hydraulic pressure.
- Worn clutch plates or bands in an automatic gearbox.
- Faulty shift solenoids, or solenoids with internal leaks.
- Input or output speed sensors faulty, with irregular signal or damaged wiring.
- Blocked or worn valve body.
- Internal mechanical wear of gears or bearings.
- Fault in the transmission ECU software, which may be corrected with an update.
The frequency of each cause depends on the type of gearbox (automated manual, conventional automatic, CVT or dual-clutch) and on the manufacturer, so the priority of checks may vary.
What to check
- Check the level and condition of the transmission fluid, following the manufacturer's procedure (some require operating temperature or the engine running).
- Read other stored codes, such as P0700, P0715, P0720 or P0750, which often accompany this fault and help locate its origin.
- Visually inspect the wiring and connectors of the speed sensors, looking for damage, corrosion or looseness.
- Use a scanner to view live data for input and output speeds and the calculated ratio in each gear, comparing them with the manufacturer's reference values.
- Measure the resistance of the solenoids and check their operation with an activation test.
- Carry out a hydraulic pressure test on the gearbox, which requires specific gauges and garage personnel.
- Do a road test to reproduce the fault and observe when it appears. It should be done by a professional or a trained person, in a safe place and with no traffic around.
- Dismantle and inspect the valve body, clutches or bands only at a garage, if the previous tests do not give a clear cause.
Frequently asked questions
Can I keep driving with code P0730 if the car changes gear properly?
Even if the gear changes seem normal, the code indicates that the transmission is not working at the correct ratio, and this may be wearing clutches, bands or internal components. Until it is checked, limit the vehicle to short, necessary trips, avoiding towing, steep hills and hard acceleration. Bear in mind that the fault can cause a sudden loss of power, which is dangerous when overtaking, joining a fast road or crossing an intersection. If the car goes into limp mode, stays in one gear, smells of burning or the warning light flashes, stop driving and call a garage or roadside assistance. It is best to have the system checked as soon as possible, because a fault that starts out minor can end up as a much more expensive repair.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.