P0013: B camshaft actuator circuit
Camshaft Position Actuator Circuit Bank 1 Camshaft "B"
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
The P0013 code is generic (SAE J2012 / ISO 15031-6) and means the ECU has detected an electrical fault in the camshaft position actuator circuit for camshaft "B" on bank 1. On many engines the "B" corresponds to the exhaust camshaft, but the designation depends on the manufacturer (≈). The actuator is usually an oil control solenoid valve that changes the angular position of the camshaft. The ECU sends a control signal and expects a consistent electrical response; if it detects an open circuit, a short to earth or to positive, or an abnormal current, it logs the fault. The type of actuator and its location vary depending on the engine.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0013? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
How the ECU detects it
The ECU checks the actuator circuit during start-up and while the engine runs, measuring the voltage and current at the solenoid valve. If the signal stays outside the expected limits continuously for a defined time, it stores the code and lights the warning lamp. On many vehicles (≈), the fault is confirmed after several consecutive driving cycles, so it may appear only under certain temperature or load conditions.
Symptoms
- Warning light (check engine light) on constantly.
- Rough or unstable idle, especially when cold.
- Slight loss of power, most noticeable when accelerating from low revs.
- Higher petrol consumption due to less efficient combustion.
- On some vehicles, the engine enters an emergency mode that limits performance.
Common causes
- Damaged actuator connector or wiring, with broken wires, corroded pins or insulation deteriorated by heat.
- Timing solenoid valve blocked by dirt or oil sludge, which can cause timing faults and, in some cases, a circuit fault.
- Solenoid valve internally faulty, with an open or short-circuited coil.
- Faulty fuse or relay supplying the actuator.
- Fault in the engine ECU or its internal drivers, uncommon.
- Poor earth or unstable power supply to the circuit, which usually appears only with the engine warm or under vibration.
What to check
- Read the code with an OBD-II reader and note the related codes and the freeze frame data.
- With the ignition off, visually inspect the solenoid valve connector: look for corroded pins, pinched wires and traces of oil.
- Check the engine oil level and condition, as degraded or sludgy oil can affect the actuator.
- Check the fuse and relay associated with the circuit according to the vehicle's wiring diagram.
- With the ignition off and the connector disconnected, measure the coil resistance with a multimeter and compare it with the manufacturer's reference value.
- Check the power supply and earth at the connector with the engine running, watching for voltage drops. Keep hands away from moving parts and hot components.
- Use the actuator test function of the diagnostic equipment to check whether the solenoid valve responds to the command.
- With the ignition off, check the continuity of the wires back to the ECU.
- If all of the above is correct, consider the ECU or an internal driver fault, after ruling out everything else.
Common diagnostic mistakes
- Replacing the solenoid valve without first checking the connector and wiring, which leaves the original fault unresolved.
- Confusing camshaft "B" with "A" and checking the wrong actuator.
- Clearing the code without repairing the cause, so the warning light will come back on.
- Measuring the coil with the connector still attached or without using the correct reference value.
- Ignoring dirt or the condition of the oil, which is a common cause of solenoid valve faults.
- Blaming the ECU without first ruling out earth or power supply faults.
Typical repairs
From the simplest and cheapest to the most expensive. Which one applies depends on the diagnosis.
- Clean the connector and restore corroded contacts, together with a check of the associated earth.
- Change the engine oil and filter if the condition of the lubricant is poor.
- Replace the fuse or relay supplying the actuator.
- Repair damaged wiring, with proper joins and heat protection.
- Replace the actuator solenoid valve with a good-quality equivalent part.
- Repair or replace the engine ECU, only if the remaining checks confirm it.
Frequently asked questions
Can I keep driving with code P0013 showing?
If the engine runs normally, you can generally keep driving, but it should be checked as soon as possible. The fault affects control of the camshaft timing and can worsen idle, consumption and performance. If you notice knocking, a strong loss of power, emergency mode, smoke or the oil pressure light, stop the vehicle in a safe place, switch off the engine and call for professional assistance.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
Related codes
- P0010 Affects the intake camshaft actuator circuit on the same bank, not the exhaust one.
- P0014 Indicates that the exhaust camshaft timing is outside the expected range, a performance problem rather than an electrical circuit fault.
- P0011 Signals intake camshaft timing that is excessively advanced, so the mechanical or control origin may be different.
- P0340 Refers to the camshaft position sensor circuit, which reports to the ECU and does not operate the timing.
- P0016 Indicates a lack of correlation between the crankshaft and the camshaft, which usually points to the timing belt or chain or to mechanical timing.
More codes: fuel, air metering and emission controls
- P0011 · Intake Camshaft Position Timing Over-Advanced or System Performance (Bank 1)
- P0014 · exhaust cam over-advanced
- P0016 · Camshaft Position – Crankshaft Position Correlation Bank 1 Sensor A
- P0019 · Crank-cam B2, sensor B
- P0020 · cam actuator bank 2
- P0022 · A cam over-retarded (bank 2)
- P0031 · heater ctrl sensor low
- P0032 · O2 sensor heater high