Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0020: cam actuator bank 2

Camshaft Position Actuator Circuit Bank 2

Severity: medium

Updated: 18 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code means the ECU detects an electrical fault in the camshaft position actuator A circuit on bank 2, that is, on the side of the engine opposite cylinder 1. On most engines, actuator A controls the intake camshaft, although this depends on the manufacturer. That actuator is usually an oil control solenoid valve that changes the camshaft angle to adjust the timing of valve opening. The ECU sends a control signal to the solenoid and monitors the voltage and continuity of the circuit. If the circuit appears open, short to earth or short to positive, or if the signal does not have the expected shape, the code is stored. This check concerns the electrical part of the actuator, not the actual position of the camshaft, which is monitored by other codes.

Can I keep driving?

Yes, but have it checked soon.

The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0020? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

How the ECU detects it

The ECU checks the actuator circuit continuously while the engine is running. An open or shorted circuit is usually detected immediately, but some intermittent faults only appear with vibration, extreme temperatures or when the engine works under certain loads. If the fault repeats over several driving cycles, the warning light comes on and the code is stored in memory.

Symptoms

  • Warning light on, sometimes flashing.
  • Uneven or slightly unstable idle, especially when cold.
  • Slight loss of power or less lively response when accelerating.
  • Higher petrol consumption with no obvious cause.
  • On some vehicles, reduced-function mode with power limited.

Common causes

  • Solenoid connector loose, corroded or with bent pins.
  • Faulty timing control solenoid, with an open or shorted coil.
  • Wiring damaged by chafing, heat or a bad join, with a break or short to earth.
  • Actuator supply fuse or relay in poor condition, depending on the vehicle design.
  • Internal fault in the engine ECU or its output stage, uncommon.
  • Dirt or degraded oil blocking the valve and causing false readings. Although this is a possible cause, the electrical fault is usually the direct cause.

What to check

  • Before disconnecting any connector, switch the ignition off. Avoid touching hot engine components.
  • Read the codes with a scanner and also note any codes related to the same bank or to the camshaft.
  • Visually inspect the solenoid connector: appearance, moisture, corrosion and locking clips.
  • Check the engine oil level and condition, because low or dirty oil can affect the actuator.
  • Measure the solenoid resistance with the engine cold and the connector disconnected, and compare with the manufacturer's value.
  • Check the supply and earth at the connector with the ignition on, using a multimeter.
  • Check the continuity of the wiring between the ECU and the solenoid, looking for breaks, shorts to earth or shorts to positive.
  • If the scanner allows, check the live data for the valve's control command and its response.
  • If all the above is correct, consider an ECU fault by testing with specialist equipment.

Common diagnostic mistakes

  • Replacing the solenoid without first checking the connector and wiring, which are usually the cause.
  • Confusing bank 1 with bank 2, especially if the vehicle has a V or boxer engine.
  • Clearing the code without checking whether it comes back, which makes it impossible to know whether the fault is resolved.
  • Ignoring the oil level and condition, which affect how the actuator works.
  • Measuring resistance with the connector connected or with the engine hot, which gives misleading readings.

Typical repairs

From the simplest and cheapest to the most expensive. Which one applies depends on the diagnosis.

  • Clean and secure the connector, removing corrosion and restoring good contact.
  • Repair the damaged wiring, with correct joins protected against chafing and heat.
  • Replace the supply fuse or relay if they are faulty.
  • Replace the timing control solenoid on bank 2.
  • Replace the engine ECU only after ruling out the other causes and with specialist verification.

Frequently asked questions

Can I keep driving with this code?

Usually yes, but it is worth having it checked soon. The fault affects control of the intake timing, so the engine may run worse or use a little more fuel. If the warning light flashes, that is not a warning specific to this code but a possible misfire. In that case, reduce engine load and take the car to the garage as soon as possible, because a misfire can damage the catalytic converter. If the engine loses power noticeably or enters reduced mode, avoid long journeys until it has been checked.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

Related codes

  • P0010 It is the same type of actuator circuit fault, but on bank 1.
  • P0021 It indicates that the bank 2 timing is excessively advanced, not an electrical circuit fault.
  • P0340 It refers to the camshaft position sensor, not the actuator that moves it.
  • P0011 It indicates that the bank 1 timing is not adjusting correctly, although the circuit is correct.
  • P0016 It indicates a loss of correlation between the crankshaft and the camshaft, and it may appear together with this one.

More codes: fuel, air metering and emission controls

All OBD codes in English