Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0016: Camshaft Position – Crankshaft Position Correlation Bank 1 Sensor A

Severity: high

Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code means the ECU detects a difference between the crankshaft position and the camshaft position on bank 1 that does not match the fixed relationship that should exist between them. The engine needs the valves to open and close at exactly the right moment in relation to the piston's rotation, and that timing is kept by the timing drive. The ECU continuously compares the signal from the crankshaft sensor with the signal from the camshaft sensor. If the relationship between the two moves outside tolerance for a set period, it stores the code and, in many cases, lights the warning lamp.

The problem may lie in the timing drive itself, in the parts that tension or guide it, in the sensors, or in the variable valve timing system. That is why the code describes a timing symptom and does not always point to the guilty part.

Can I keep driving?

Only as far as you need to, and gently.

This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0016? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Check engine warning lamp on, sometimes flashing.
  • Rough or unstable idle.
  • Loss of power and weak response when accelerating.
  • Difficulty starting, especially when cold or after several hours standing.
  • Audible timing chain or belt noise, or tension noise, around the cylinder head or timing cover.
  • Slightly higher fuel consumption than usual.
  • In some cases, the engine shows no clear symptoms and the code appears intermittently.

Common causes

  • Stretched timing chain or worn timing belt, which shifts the relationship between crankshaft and camshaft.
  • Jumped teeth on the belt or sprocket, leaving the timing out of step.
  • Worn tensioner or chain guides, allowing play and position variation.
  • Faulty, dirty or badly fitted camshaft or crankshaft sensor.
  • Damaged reluctor wheel or sensor rotor, with broken or misaligned teeth.
  • Corroded, broken or intermittently contacting sensor wiring or connectors.
  • Variable valve timing (VVT) solenoid or actuator stuck, with dirty oil or insufficient pressure.
  • Low or degraded engine oil, which affects the operation of the phaser.

The most likely cause depends on the engine and the manufacturer, and cannot be determined without diagnosis. On chain-driven engines, stretch is a common cause with mileage. On belt-driven engines, the origin may lie in the tensioner, the belt or the sensors. On engines with variable valve timing, the VVT solenoid and the condition of the oil can be decisive in cases with no visible mechanical wear, although this varies by model.

What to check

  • Check the oil level and condition, and whether there is a record of a recent oil change.
  • Look for other fault codes related to timing or variable valve timing, as they may indicate the source.
  • Visually inspect the connectors and wiring of the crankshaft and camshaft sensors.
  • Clean and check the condition of the sensors and the reluctor wheel, and do not overlook mounting play.
  • Listen to the engine when cold and on start-up for chain or belt noises.
  • Check the sensor signals with an oscilloscope or diagnostic tool, observing the waveforms and the relationship between both signals.
  • Test the VVT solenoid and confirm that the actuator moves freely.
  • Verify the alignment of the timing marks. This check requires removing covers and, depending on the engine, may involve dismantling further parts. It must be carried out following the manufacturer's procedure and torque settings. Never turn the engine with the timing disconnected or without the locking tools specified, as this can damage valves and pistons.
  • Measure chain stretch or inspect the condition of the belt, tensioner and guides. This is the most complex check and the one that confirms or rules out a mechanical fault. If you do not have the tool or the manufacturer's technical information, it is best to entrust the job to a specialist garage.

Frequently asked questions

Can I keep driving with code P0016 if the car runs fine?

It is not advisable to keep driving normally. The fault may be intermittent and the engine may seem fine, but a timing that is out of step can get worse and, on interference engines, damage valves and pistons. If you notice timing noises, loss of power, rough idle or difficulty starting, do not keep driving: stop the vehicle somewhere safe and call for roadside assistance or a tow to the garage. If the car runs normally, limit its use and have it inspected as soon as possible to check the timing drive and the variable valve timing system.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: fuel, air metering and emission controls

All OBD codes in English