Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0022: A cam over-retarded (bank 2)

Camshaft Position "A" – Timing Over-Retarded (Bank 2)

Severity: medium

Updated: 18 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code means the ECU detects that the camshaft on bank 2 is more retarded than it should be, according to the position the variable valve timing system is commanding. The ECU compares the actual camshaft position, measured by the camshaft position sensor, with the target position calculated from engine load, temperature, speed and crankshaft position. If the difference stays out of tolerance for long enough, it stores the code and may switch on the warning light. Bank 2 is the group of cylinders that does not contain cylinder number 1, and on V or boxer engines there is usually a separate camshaft for each bank. That is why the code refers to a side of the engine, not to a specific cylinder.

Can I keep driving?

Yes, but have it checked soon.

The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0022? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

How the ECU detects it

  • The ECU evaluates this code continuously, but only confirms it when the difference between actual and target position exceeds the threshold over several driving cycles.
  • It usually appears with the engine already warm and under demand, such as accelerating or going uphill, when the variator has to act with more pressure and speed.
  • If the fault is intermittent, the light may come on and go off depending on temperature, load and oil level conditions.

Symptoms

  • Warning light on, sometimes flashing if the fault is severe.
  • Rough or unstable idle, especially when the engine is warm.
  • Loss of power or sluggish response when accelerating.
  • Higher fuel consumption than usual.
  • Slight jerking when driving at a steady speed or going uphill.
  • Slightly slower starting, especially when cold or after a long stop.
  • In some cases nothing is noticeable and the fault only appears when the memory is read.

Common causes

  • Low oil level or very old oil, which reduces the pressure needed to move the timing variator.
  • Dirty, stuck or sludge-blocked timing variator oil control valve.
  • Clogged mesh filter at the timing variator oil inlet.
  • Worn timing variator (actuator), with play or with damaged spring or internal parts.
  • Stretched timing chain or belt, with tooth jump or wear, which shifts the relationship between crankshaft and camshaft.
  • Faulty or irregular signal from the bank 2 camshaft position sensor.
  • Damaged sensor or valve wiring or connectors, with corrosion or poor contacts.
  • ECU or software fault, uncommon but possible.
  • Worn hydraulic tensioner or chain guides, allowing the timing to shift.

The significance of each cause depends on the manufacturer and the engine. Check the data for the specific vehicle.

What to check

  • Check the oil level and condition with the engine in the conditions the manufacturer specifies. A low level or dark, degraded oil is a first point to correct.
  • Read the related codes with a scanner (bank 1 and bank 2) and check whether there are other timing or crankshaft and camshaft sensor codes. Note the freeze-frame data from the moment of the fault.
  • Watch the live actual and target camshaft position values for bank 2 with the engine at idle and with a slight rise in revs. A large, constant difference points to a pressure, valve or actuator problem.
  • Check the condition of the connector and wiring of the sensor and of the variator control valve: look for damage, corrosion and poor contacts. If you need to move the cables with the engine running, do so carefully and without touching moving or hot parts; it is safest to do it with the engine off.
  • Inspect the oil control valve and, if the manufacturer allows, clean or replace it. Also check the variator inlet filter.
  • Check the engine oil pressure with a gauge, as low pressure limits the variator's operation.
  • Check whether the engine noise when cold, a buzz or a rattle on start-up indicates a worn chain or tensioner. On many engines this check requires removing the timing cover, so it is usually a job for a garage.
  • As a last step, check the timing against the manufacturer's reference marks and assess the condition of the variator, the chain or belt, and its guides and tensioners. This task should be done by a professional.

Common diagnostic mistakes

  • Replacing the position sensor without first checking the oil level, its condition and the pressure, when oil is a frequent cause.
  • Cleaning or replacing the control valve without checking the variator inlet filter, which can clog the valve again.
  • Assuming the fault is fixed after clearing the code without checking whether it returns on a later driving cycle.
  • Confusing bank 1 with bank 2 and checking the wrong side of the engine.
  • Ignoring a chain noise when cold, which can be the first symptom of a stretched timing chain.
  • Assuming the problem is mechanical without first assessing the electrical and control system.
  • Continuing to drive with timing noise or power loss without being clear about the extent of the damage.

Typical repairs

From the simplest and cheapest to the most expensive. Which one applies depends on the diagnosis.

  • Top up the oil level and replace the oil with the type and specification the manufacturer gives, if its condition justifies it.
  • Clean the variator oil control valve and check or replace its inlet filter.
  • Repair or replace the bank 2 camshaft position sensor connector, wiring or sensor when an electrical fault is found.
  • Replace the variator oil control valve if it does not respond correctly.
  • Replace the bank 2 variator or phaser actuator when it shows play, wear or malfunction.
  • Change the timing chain or belt together with tensioners and guides if they are worn or stretched, and check the timing. This repair should be done by a specialist garage.
  • As a last resort, replace or reprogram the ECU if all other checks are correct.

Frequently asked questions

Can I keep driving with code P0022 (camshaft position "A" timing over-retarded, bank 2)?

It depends on the cause and how far the timing has drifted. If the fault appears occasionally and the engine runs normally, you can drive for a few days with caution, avoiding high loads, and have the vehicle checked as soon as possible. If there is jerking, clear loss of power, a flashing warning light, or chain noise or knocking, do not keep driving: use the vehicle as little as possible and take it to a garage, by tow truck if necessary. Mistimed valves can cause serious engine damage, including contact between valves and pistons in interference engines, and in that case the repair can be expensive.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

Related codes

  • P0021 It is the same type of fault but in the opposite direction: the bank 2 camshaft is more advanced than expected, not more retarded.
  • P0011 It refers to the bank 1 camshaft "A", so it affects the other side of the engine.
  • P0020 It indicates an electrical fault in the bank 2 actuator circuit, not a position mismatch.
  • P0018 It signals a loss of correlation between the crankshaft and the bank 2 camshaft, which points to a physical timing or sensor problem.
  • P0345 It refers to the camshaft position sensor circuit "A" on bank 2, so it is worth ruling out a signal fault before blaming the variator.

More codes: fuel, air metering and emission controls

All OBD codes in English