P0036: sensor behind cat
O2 Sensor Heater Control Circuit Bank 1 Sensor 2
Severity: medium
Updated: 18 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
The code indicates that the engine control module (PCM) has detected a fault in the circuit that supplies and controls the heating element of the lambda sensor located after the catalytic converter on bank 1. This sensor, usually called sensor 2, is mainly used to monitor whether the catalytic converter is still working properly, not to adjust the fuel mixture in real time. The ECU usually controls the heater by modulation and checks the current or the electrical response of the circuit; if the value falls outside the expected ranges for that operating point, it records the fault. The heater allows the sensor to reach its working temperature quickly, so that the system does not depend only on hot exhaust gases.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0036? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
How the ECU detects it
- The ECU monitors the heater circuit continuously while the engine runs, and also during some checks with the ignition on.
- Usually the fault is confirmed after the anomaly is detected over several driving cycles, so the lamp may not come on the first time you start the car.
- Many systems evaluate the heater only under certain engine temperature and speed conditions, so the fault may appear only on certain journeys.
- When the lamp comes on, a pending or confirmed code is normally stored that identifies when the anomaly occurred.
Symptoms
- The malfunction indicator lamp (MIL) comes on, sometimes after several driving cycles in which the same condition repeats.
- Normally there are no driving symptoms; the fault is usually detected when reading the ECU.
- As this sensor does not control the mixture in real time, the fault does not usually cause by itself jerking, rough idle or increased fuel consumption.
- In emissions checks the catalyst or sensor monitors may not pass, even though the car is running normally.
Common causes
- Blown or poorly connected heater fuse or relay.
- Sensor connector corroded, loose or with moisture inside.
- Heater wire cut, crushed or chafed by the exhaust or by a moving part.
- Internal resistance of the sensor heater worn out or open, which can occur with ageing.
- Short to earth or to positive in the sensor wiring.
- Fault in the ECU driver that controls the heater, less common and usually ruled out last.
- Fault in the general ECU power supply or earth, which can cause wrong readings in several circuits at once.
What to check
- Safety warning: with the engine hot, the exhaust and the sensor can cause burns; wait for them to cool before touching them. Measurements must be made with the ignition off and the sensor disconnected, and any work under the vehicle must be done with the car securely supported.
- Consult the manufacturer's documentation to locate the bank 1 sensor 2 sensor (the one after the catalytic converter) and its connector, as the sensor type and wiring vary between vehicles.
- Visually inspect the sensor connector and wiring, looking for heat damage, chafing, moisture or greenish pins.
- Check the fuse and relay that supply the oxygen sensor heaters according to the vehicle's wiring diagram.
- With the engine off and the sensor disconnected, measure the heater resistance between the corresponding pins with a multimeter and compare it with the manufacturer's reference value.
- Check the continuity of the wiring between the sensor connector and the ECU, and the absence of shorts to earth or to positive.
- With the engine running and live data, observe the heater control and circuit status, comparing it with the bank 1 sensor 1 sensor to detect differences.
- If all of the above is correct, consider replacing the sensor and only then suspect the ECU, after ruling out earths and power supplies.
Common diagnostic mistakes
- Replacing the sensor without first measuring the heater or checking the wiring, which can leave the original fault unresolved.
- Confusing bank 1 sensor 2 with bank 1 sensor 1, leading to checking the wrong sensor.
- Ignoring a damp connector or corroded pins, which is a very common cause and easy to fix.
- Measuring resistance with the sensor still connected to the ECU, which gives misleading readings.
- Clearing the code without repairing the cause, so the lamp will come back after the next driving cycles.
Typical repairs
From the simplest and cheapest to the most expensive. Which one applies depends on the diagnosis.
- Clean the connector, remove moisture and restore contact on the pins.
- Replace the heater fuse or relay if damaged.
- Repair damaged wiring, with properly insulated joins or replacement of the affected section.
- Replace the bank 1 sensor 2 lambda sensor if its heater is open or out of specification.
- Diagnose and repair the ECU power supply or earth if a lack of voltage or reference is found.
- Replace or reprogram the ECU only after ruling out all the components above.
Frequently asked questions
Can I keep driving with code P0036 showing?
In general yes, because the fault affects the warm-up of a sensor that does not control the mixture in real time. Even so, it is best to check it soon, because the catalytic converter is left without proper monitoring and the car may fail the emissions test. If jerking, high fuel consumption or other symptoms also appear, the check should be more urgent, as there may be another associated fault.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
Related codes
- P0030 Affects the same type of circuit, but for the bank 1 sensor 1 heater, which is the main sensor before the catalytic converter.
- P0037 Indicates that the bank 1 sensor 2 heater has a low signal or voltage level, whereas P0036 describes a fault in the circuit control.
- P0038 Indicates that the bank 1 sensor 2 heater has a high signal or voltage level, so the electrical symptom is the opposite.
- P0136 Refers to a fault in the signal circuit of the bank 1 sensor 2 sensor, not to the heater circuit.