P0175: Bank 2 Fuel Trim System Too Rich
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
The code indicates that, on bank 2 of the engine (the side that does not contain cylinder 1), the ECU detects that the air-fuel mixture is richer than expected. To detect it, it compares the signal from the lambda sensors with the short-term and long-term fuel trim adjustments. When these adjustments reach the limit of correction and the system fails to balance the mixture, it lights the warning lamp after confirming the fault over several driving cycles. An excess of fuel may be due to a fault in measurement, pressure, air or injection. The code does not identify by itself the faulty part; it only describes the symptom of the mixture.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0175? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Check engine warning lamp lit (sometimes it is the only symptom)
- Higher fuel consumption than usual
- Smell of unburnt petrol from the exhaust
- Uneven or shaky idle when stopped
- Loss of power or slightly slow response when accelerating
- Dark or black smoke from the exhaust
- Blackened spark plugs or spark plugs covered in soot
Common causes
- Bank 2 lambda sensor giving an incorrect reading, contaminated or aged
- Mass air flow sensor (MAF) dirty or faulty, underestimating the air admitted
- Bank 2 injector that drips or stays partially open
- Excessive fuel pressure due to a faulty regulator or pressure sensor
- EVAP purge valve stuck in the open position
- Coolant temperature sensor giving an incorrect reading, which makes the mixture enrich when cold
- Air filter clogged or air intake restricted
- Faulty MAP sensor (manifold absolute pressure), on engines that fit one
What to check
- Working on the fuel system requires precautions: no flames or sparks, work in a ventilated area and depressurise the circuit before disconnecting components. If you have no experience, leave these tests to the garage.
- Check the air filter and the intake ducts
- Read the related codes (for example, the lean mixture code for the same bank) and watch the live fuel trim data
- Inspect the bank 2 spark plugs: black, wet or smelling of fuel indicates a rich mixture
- Check for vacuum leaks that could confuse the air measurement
- Verify the MAF reading in live data and clean it with a specific cleaner if appropriate
- Measure the fuel pressure at the rail and compare it with the manufacturer's specification
- Check the lambda sensor: response time, wiring, heater and voltage
- Test the bank 2 injectors (flow, leaks and behaviour when switched off)
- Check the EVAP purge valve and its operation
- Check the coolant temperature sensor and its reading against the actual temperature
Frequently asked questions
Can I keep driving with the check engine light on for P0175?
In general, yes in the short term, but it should be checked soon. An excess of fuel can foul the catalytic converter and the spark plugs, increase consumption and, over time, dilute the engine oil. If the lamp flashes, there is a serious fault: stop the engine and do not keep using it. If the engine shakes, loses power or smells strongly of petrol, reduce speed, ventilate the vehicle and take it to the garage as soon as possible. Do not try to locate fuel leaks with a flame or sparks nearby.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: fuel and air metering
- P0128 · Engine Coolant Temperature Below Thermostat Regulating Temperature
- P0133 · Oxygen (Lambda) Sensor Circuit Slow Response, Bank 1 Sensor 1
- P0135 · Heated Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
- P0141 · Heated Oxygen Sensor Circuit Bank 1 Sensor 2
- P0171 · System too lean (Bank 1)
- P0172 · Fuel System Too Rich (Bank 1)
- P0174 · System Too Lean (Bank 2)
- P0191 · Fuel Rail Pressure Sensor 'A' Circuit Range/Performance