P0191: Fuel Rail Pressure Sensor 'A' Circuit Range/Performance
Severity: high
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
DTC P0191 corresponds to a range or performance fault in the fuel rail pressure sensor 'A'. Unlike circuit codes (such as P0190), the electrical signal may be plausible, but its value falls outside the range expected for the operating conditions, or the actual pressure does not follow the desired pressure commanded by the ECU to the pump or the regulator valve. The ECU continuously compares the measured pressure with the target; if the difference exceeds a threshold for a set time, it stores the code and, depending on the manufacturer's strategy, may activate an emergency mode. The exact thresholds, detection time and reaction strategy depend on the make, the engine and the software version, so they are not the same in every vehicle.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0191? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Loss of power or emergency mode (limp mode).
- Difficulty starting or irregular cranking.
- Unstable idle or stalling when coming to a stop.
- Jerking or hesitation when accelerating.
- Higher fuel consumption than usual.
- Warning light on, sometimes flashing.
Common causes
- Faulty fuel rail pressure sensor or one with reading drift.
- Damaged connector or wiring: corrosion, crushed harness, or poor earth or power supply.
- Low actual pressure in the line due to a leak, blocked filter or weakened pump (low or high pressure).
- Regulator or metering valve stuck or with an electrical fault (depending on the system).
- ECU fault or outdated software (less common).
What to check
- Inspect the sensor connector: corrosion, bent pins or damaged cable.
- Check the fuel level and condition, and whether the filter is blocked.
- Read live data with the scanner: actual pressure versus desired pressure at idle and at different engine speeds.
- Check the sensor's supply voltage, signal and earth with a multimeter or oscilloscope, according to the manufacturer's wiring diagram.
- Look for leaks in the high and low pressure lines, without touching pressurised pipes.
- Assess the high-pressure pump and the regulator valve following the manufacturer's procedure. WARNING: the system can operate at very high pressures (≈ 200 bar in direct-injection petrol and more than 1,500 bar in diesel common rail). Before disconnecting any component, the pressure must be relieved according to the manual, and the fuel is flammable. This part should be done by a professional with the proper equipment.
- Consult the manufacturer's technical bulletins and check whether there is an ECU software update.
Frequently asked questions
Can I keep driving with code P0191?
It depends on how the car behaves. If it drives normally, with no jerking or loss of power, it can be taken with caution to a garage in the near future, without pushing it. If the engine stalls, is hard to start, goes into emergency mode or you smell fuel, you should not keep driving, because incorrect pressure can leave the engine without fuel in the middle of a journey. In that case, the safest option is to call a recovery service. Inspection of the high-pressure components should be carried out by a professional.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: fuel and air metering
- P0128 · Engine Coolant Temperature Below Thermostat Regulating Temperature
- P0133 · Oxygen (Lambda) Sensor Circuit Slow Response, Bank 1 Sensor 1
- P0135 · Heated Oxygen Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
- P0141 · Heated Oxygen Sensor Circuit Bank 1 Sensor 2
- P0171 · System too lean (Bank 1)
- P0172 · Fuel System Too Rich (Bank 1)
- P0174 · System Too Lean (Bank 2)
- P0175 · Bank 2 Fuel Trim System Too Rich