Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P2002: Diesel Particulate Filter (DPF) Efficiency Below Threshold (Bank 1)

Severity: medium

Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code means the ECU considers that the diesel particulate filter is not retaining soot with the minimum expected efficiency on bank 1. To detect it, the ECU compares the signal from the differential pressure and temperature sensors before and after the filter with the values it should have, based on engine load and the distance driven since the last regeneration. If the difference repeatedly does not match the reference model, the code is stored. Low efficiency is usually due to a deteriorated, cracked or saturated filter, or to the sensors monitoring it giving erroneous readings. The ECU does not always distinguish between both causes, so the diagnosis must be completed with physical tests.

Can I keep driving?

Yes, but have it checked soon.

The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P2002? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Warning light or diesel particulate filter light on in the instrument cluster
  • Loss of power, especially when accelerating or climbing hills
  • More frequent regenerations than normal, or regenerations that do not complete
  • Increased fuel consumption
  • Darker exhaust smoke than usual
  • In some vehicles, radiator fan running longer after switching off the engine, due to the regenerations
  • In some vehicles, entry into limp (reduced operation) mode

Common causes

  • Particulate filter saturated with soot, common on short journeys where regenerations do not complete
  • Incomplete regenerations due to faults in the injection system or combustion management
  • Differential pressure or temperature sensors for the filter giving erroneous readings, due to wear, deteriorated connections or blocked pressure hoses
  • Exhaust leaks before or after the filter that alter the pressure readings
  • Filter cracked or internally damaged, with particles passing through
  • Build-up of ash from engine oil that is not removed by regeneration
  • Regeneration strategies and diagnostic thresholds differ by make and model, so the most likely cause varies from one vehicle to another

What to check

  • Review the usage history: if the car mainly makes short journeys, the filter has probably become saturated
  • Check for other fault codes related to injection, pressure or temperature sensors in the exhaust
  • Visually inspect the electrical connections and the differential pressure sensor hoses
  • Look for exhaust leaks with the engine running, paying attention to gaskets and clamps before and after the filter
  • Read the live differential pressure and filter temperature values with a scanner, comparing them with the values expected for the operating speed according to the manufacturer
  • Carry out a forced regeneration with diagnostic equipment and check whether the pressure reading returns to normal
  • Measure exhaust back pressure or inspect the removed filter to detect blockage, cracks or ash build-up
  • If the filter is damaged or does not recover its efficiency after cleaning, consider replacing it through a professional
  • Caution: the exhaust and the filter can reach very high temperatures during regeneration. Do not touch the hot system, do not work under the vehicle right after the engine has stopped, and do not run the engine in a closed garage without ventilation
  • Forced regeneration, cleaning and filter replacement must be carried out by professionals with suitable equipment

Frequently asked questions

Can I keep driving with code P2002 active?

It depends on the symptoms. If the filter warning light flashes, you notice a strong loss of power, heavy smoke or abnormal smell, or the car enters reduced mode, do not keep driving: stop in a safe place, switch off the engine and go to a garage. If only the warning light is on and you notice no symptoms, you can drive carefully in the short term, avoiding short journeys and not forcing the engine, and have it checked soon so the filter does not become more saturated.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: fuel, air metering and emission controls

All OBD codes in English