P0405: EGR Sensor A Circuit Low
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
Code P0405 means the engine control unit detects a voltage from the EGR valve position sensor A that is below the expected range. The EGR valve recirculates part of the exhaust gases back into the intake to reduce nitrogen oxide emissions, and the sensor tells the ECU how far open the valve is. To do this, the ECU supplies the sensor with a reference voltage and reads a signal that changes with the valve position. If that signal falls below the minimum limit during the verification time, or if the circuit has a short to earth or an open circuit, the fault is logged. It is an electrical circuit fault, which does not always mean the valve itself is faulty.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0405? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Malfunction indicator light (MIL) lit on the instrument cluster.
- Rough or unstable idle, especially when cold.
- Slight loss of power or a slightly less smooth response when accelerating.
- Fuel consumption slightly higher than usual.
- On some vehicles, the ECU limits or disables exhaust gas recirculation, and the engine may run with few noticeable symptoms.
Common causes
- Sensor connector corroded, loose or with bent pins.
- Signal or earth wire damaged (chafing, deteriorated insulation or contact with earth).
- Faulty EGR sensor, with the signal out of range.
- Fault in the sensor's reference supply or its earth.
- EGR valve stuck or clogged with carbon, which can cause abnormal readings (the cause depends on the manufacturer and on whether the sensor is integrated into the valve).
- ECU with an internal fault (this is the least common cause).
What to check
- Safety: with the engine hot, the exhaust manifold and the EGR valve can cause burns; wait for them to cool before touching them. When checking with the engine running, keep well clear of the fan, the belt and other moving parts.
- Visually inspect the EGR sensor connector: corroded, dirty or bent pins, and whether the lock is firm.
- Inspect the harness along its visible route, looking for chafing, burns from manifold heat or stripped wires.
- Check the circuit earth and the reference voltage with a multimeter, according to the manufacturer's wiring diagram.
- Read the live EGR position data with a scanner and compare it with the value requested by the ECU, with the engine at idle and under load.
- Move the harness and connector with the engine running to detect intermittent faults, without bringing your hands close to moving parts.
- Check the EGR valve physically (carbon obstruction, stem movement) and, if possible, replace the sensor with a tested one to rule out the fault.
- Analyse the signal with an oscilloscope, if the garage has one, to detect drops or interruptions.
- Consider the ECU only after ruling out all of the above.
Frequently asked questions
Can I keep driving with code P0405 showing?
In general yes, as long as the vehicle runs normally and you do not notice jerking, loss of power or a very rough idle. The fault affects emissions control and does not usually compromise safety in the short term. Even so, it is best to get it checked soon, because a sensor giving an incorrect signal can make the engine run worse and, over time, could damage the valve or increase carbon build-up in the intake.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: auxiliary emission controls
- P0401 · Insufficient Exhaust Gas Recirculation (EGR) Flow Detected
- P0402 · Excessive Exhaust Gas Recirculation (EGR) Flow
- P0406 · EGR Sensor A Circuit High
- P0411 · Incorrect Flow Detected in Secondary Air Injection System
- P0420 · Catalyst system efficiency below threshold (bank 1)
- P0421 · catalyst inefficient
- P0422 · catalyst below efficiency
- P0430 · Catalyst System Efficiency Below Threshold (Bank 2)