P0430: Catalyst System Efficiency Below Threshold (Bank 2)
Severity: medium
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code means the ECU considers the catalytic converter on bank 2 is not reducing exhaust pollutants with the minimum efficiency required. Bank 2 is the cylinder bank that does not contain cylinder 1. To check this, the ECU compares the signal from the oxygen sensor located behind the catalytic converter with the one located in front of it. If the catalytic converter is working properly, the downstream signal should be much more stable and show fewer oscillations than the upstream one. When the downstream oscillations begin to resemble the upstream ones too closely, the system concludes that the catalytic converter is no longer storing and processing oxygen as it should, and it sets the code.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0430? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Check engine light comes on, sometimes with no other visible symptoms.
- Slight loss of power or a somewhat more uneven response in some cases.
- Moderate increase in fuel consumption.
- Smell of sulphur or rotten eggs from the exhaust, especially during acceleration or after cold starts.
- In some cases, the code appears together with other misfire or oxygen sensor codes.
Common causes
- Bank 2 catalytic converter degraded through ageing or normal use over the years.
- Bank 2 downstream oxygen sensor responding slowly, aged or faulty, which the ECU interprets as an ineffective catalytic converter.
- Exhaust leaks located between the manifold and the downstream sensor, which distort the readings.
- Mixture running continuously rich or lean, with excess fuel or air, due to injectors, the upstream sensor or intake sensors.
- Repeated misfires that send unburnt fuel to the catalytic converter, overheating or contaminating it.
- Catalytic converter contamination by oil or coolant, for example from oil consumption or gasket problems.
- Internal mechanical damage to the catalytic converter, such as melting or breaking up, although this is less common.
- The relative importance of each cause depends greatly on the model, the mileage and the type of catalytic converter, so it is not possible to set an exact order valid for all makes.
What to check
- Check whether other codes are stored, especially for misfires, oxygen sensors or mixture, as these often explain the problem.
- Visually inspect the exhaust for leaks, whistling, soot or deteriorated welds, paying attention to the area between the manifold and the downstream sensor.
- Look at live oxygen sensor data: the downstream signal should be fairly stable and oscillate little, while the upstream one oscillates quickly.
- Check that both sensors heat up properly and respond quickly, reviewing their heater resistance and their response in live data.
- Verify the mixture adjustments using the short-term and long-term fuel trim data, to detect persistent rich or lean mixtures.
- Check for misfires with an analyser or by checking the spark plugs, coils and injectors on bank 2.
- Measure the temperature at the inlet and outlet of the catalytic converter with a contact or infrared thermometer, comparing the two: a very small difference suggests an exhausted catalytic converter.
- Measure exhaust back-pressure to rule out an internal blockage of the catalytic converter.
- Check the level and condition of the oil and coolant to rule out contamination of the catalytic converter.
- As a last step, inspect the inside of the catalytic converter or replace it if the other checks confirm it.
Frequently asked questions
Can I keep driving with code P0430 showing?
With the warning light steady you can drive for a short time, as the code itself does not usually prevent normal driving. Even so, it is best to have it checked soon, since a deteriorated catalytic converter loses efficiency and can end up overheating. If the light is flashing, or you notice jerking, loss of power or a strong smell of sulphur, do not keep driving: flashing usually indicates serious misfires that can damage the catalytic converter, and a very hot catalytic converter can cause a fire, especially if it is near dry grass or other flammable materials. Reduce the engine load and take the vehicle to a garage as soon as possible, or call a recovery service if necessary.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: auxiliary emission controls
- P0411 · Incorrect Flow Detected in Secondary Air Injection System
- P0420 · Catalyst system efficiency below threshold (bank 1)
- P0421 · catalyst inefficient
- P0422 · catalyst below efficiency
- P0440 · Evaporative Emission Control System Malfunction
- P0442 · Small Evaporative Emission Control System Leak Detected
- P0446 · EVAP Ventilation Control Circuit Malfunction
- P0450 · EVAP pressure sensor