P0411: Incorrect Flow Detected in Secondary Air Injection System
Severity: low
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
The code indicates that the ECU has detected an air flow different from the expected one in the secondary air injection system. This system pushes fresh air into the exhaust shortly after a cold start, so that the oxygen helps burn unburnt hydrocarbons and the catalytic converter reaches its working temperature sooner. To monitor it, the ECU may use the response of the lambda sensor located upstream of the catalytic converter, the reading of a pressure or flow sensor, or both, comparing them with reference values during a specific test. The exact strategy varies by manufacturer. If the measured flow does not match the expected flow, it logs the fault and, in most cases, turns on the warning light. The code does not point to one specific part, but to a mismatch between the air the system is commanded to inject and the air that actually flows.
Can I keep driving?
Yes, it does not affect driving in the short term.
You can keep using the car normally, but do not ignore it: have it checked at your next service or if the warning light comes back after clearing it.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0411? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Warning light on in the instrument cluster, which is usually the only visible symptom.
- Slightly uneven idle or a slight jerk during the first few minutes after a cold start, although it does not always appear.
- Air pump noise on a cold start, or absence of that noise if the pump is not working.
- Slightly higher fuel consumption or emissions on cold starts, which only becomes noticeable if monitored.
Common causes
- Check valve stuck, cracked or leaking, letting exhaust gases flow back into the system.
- Secondary air pump with a mechanical or electrical fault, or with a faulty relay.
- Hoses or pipes cracked, disconnected or leaking, especially near the manifold or the cylinder head.
- Secondary air control valve stuck open or closed.
- Faulty system pressure or flow sensor, or with readings outside the range.
- Damaged connector or wiring, with a poor earth or unstable power supply.
- ECU software fault, which is uncommon.
- Note: the design and the order of probability of these causes depend on the make and model, as not all vehicles fit this system or in the same configuration.
What to check
- Caution: the manifold, exhaust pipe and catalytic converter may be very hot. Wait for them to cool before touching pipes, valves or the pump.
- Visual inspection of hoses, pipes and connections of the secondary air system, looking for cracks, looseness or soot deposits.
- Check the fuses and relays for the secondary air pump in the fuse box.
- Listen whether the pump activates on a cold start and during the first minutes of operation.
- Check the connectors and wiring of the pump, the control valve and the pressure sensor, looking for corrosion or damage. If the manufacturer's procedure specifies it, disconnect the battery before disconnecting connectors.
- Read live data with a scan tool to check the status of the pump and valve and, if the equipment allows, activate them in test mode.
- Check the check valve, using vacuum or pressure according to the manufacturer's procedure.
- Measure pressure or flow in the system and compare with the manufacturer's specifications.
- Verify the pressure or flow sensor, replacing it only if its fault is confirmed.
Frequently asked questions
Can I keep driving with code P0411 on?
Usually yes, because the fault mainly affects emissions during cold starts and does not normally compromise safety or engine running. It is advisable, however, not to delay the check for long: a leak or a pump fault can get worse over time, and the code may prevent you from passing the periodic roadworthiness test (MOT in the UK) or the emissions check in some countries. If the car shows strong jerking, loss of power, temperature or oil pressure warnings, or a strong smell of petrol, it should be checked before driving on. The smell of fuel is not related to this code: in that case, stop the car and call a professional.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: auxiliary emission controls
- P0401 · Insufficient Exhaust Gas Recirculation (EGR) Flow Detected
- P0402 · Excessive Exhaust Gas Recirculation (EGR) Flow
- P0405 · EGR Sensor A Circuit Low
- P0406 · EGR Sensor A Circuit High
- P0420 · Catalyst system efficiency below threshold (bank 1)
- P0421 · catalyst inefficient
- P0422 · catalyst below efficiency
- P0430 · Catalyst System Efficiency Below Threshold (Bank 2)