P0420: Catalyst system efficiency below threshold (bank 1)
Severity: medium
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
The code indicates that the efficiency of the catalytic converter on bank 1 is below the threshold the ECU considers acceptable. To check this, the ECU compares the signal from the lambda sensor fitted before the catalytic converter with that of the rear sensor. If the catalytic converter is working properly, the rear signal is much more stable and changes less than the front one. When both signals look too similar, the ECU concludes that the catalytic converter is no longer storing and converting oxygen and polluting gases properly. The code is usually stored after several driving cycles under stable conditions, so it does not appear straight away. Bank 1 is the side of the engine on which cylinder number 1 is located.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0420? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Steady illumination of the malfunction indicator lamp (MIL). If the code appears together with active misfires, the lamp may flash; in that case, deal with the misfire first.
- Usually nothing noticeable when driving.
- In some cases, the engine may respond slightly worse or use a little more petrol, but these symptoms are not common and depend on the vehicle.
- A sulphur or rotten egg smell from the exhaust, especially with the engine warm.
- If the catalytic converter is badly damaged or overheated, the exhaust area can reach very high temperatures.
Common causes
- Normal wear of the catalytic converter due to age or accumulated mileage.
- Catalytic converter damaged by prolonged misfires, which send unburnt fuel into the exhaust.
- Contamination of the catalytic converter by burnt oil, coolant or unsuitable additives.
- Degraded rear lambda sensor, providing an unreliable reading.
- Exhaust leaks before the rear sensor, which alter the oxygen reading.
- Unbalanced air-fuel mixture over long periods (too rich or too lean).
- Intermittent faults in the sensors or wiring. The location and type of sensors depend on the make and model, so it is worth consulting the manufacturer's documentation.
What to check
- Check whether there are other stored codes, especially misfires (P030X) or lambda sensor codes, and resolve them first.
- Before working under the vehicle, raise it only with approved ramps or axle stands, never with a jack alone, and let the exhaust cool down. A hot exhaust can cause serious burns.
- Visually inspect the exhaust for leaks, cracks or hissing before the rear sensor.
- Check the maintenance history and whether the engine has been using oil or coolant.
- Use a scanner to observe the live data from both lambda sensors with the engine warm: the rear one should be stable and almost flat, not reflecting the oscillations of the front one.
- Check the electrical condition of the sensors: connectors, wiring, earth and heater supply. With the engine running, do not touch the exhaust or other hot components.
- Measure the condition of the catalytic converter with a gas analyser or an exhaust back-pressure test, bearing in mind that the result depends on the design of each engine. If the result is not clear, take the vehicle to a specialist garage.
- Confirm the diagnosis before replacing the catalytic converter, because it is an expensive part and sometimes the problem lies with the sensors or the mixture.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: auxiliary emission controls
- P0401 · Insufficient Exhaust Gas Recirculation (EGR) Flow Detected
- P0402 · Excessive Exhaust Gas Recirculation (EGR) Flow
- P0405 · EGR Sensor A Circuit Low
- P0406 · EGR Sensor A Circuit High
- P0411 · Incorrect Flow Detected in Secondary Air Injection System
- P0421 · catalyst inefficient
- P0422 · catalyst below efficiency
- P0430 · Catalyst System Efficiency Below Threshold (Bank 2)