P0422: catalyst below efficiency
Catalyst System Efficiency Below Threshold (Bank 1)
Severity: medium
Updated: 21 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
Code P0422 means the engine control unit has detected that the catalytic converter on bank 1 is not reducing pollutants as effectively as expected. To assess it, the ECU compares the signals from the two lambda sensors: the sensor before the catalytic converter (upstream sensor) and the one after it (downstream sensor). A catalytic converter in good condition stores and transforms oxygen, so the signal from the downstream sensor should be much more stable than that from the upstream sensor. When both signals look too similar, the ECU concludes that the catalytic converter no longer performs its function and records the fault. Bear in mind that, in many cases, the catalytic converter is not actually worn out: the cause may be a downstream lambda sensor with a slow response, an exhaust leak that lets in false air, or a mixture problem that overloads the catalytic converter.
Can I keep driving?
Yes, but have it checked soon.
The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0422? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
How the ECU detects it
The ECU assesses the efficiency of the catalytic converter continuously during driving, when the engine is at operating temperature and in closed-loop mixture control. It compares the activity of the upstream and downstream sensors under stable load and speed conditions. If after several driving cycles that difference does not reach the programmed threshold, it switches on the light and stores the code. That is why the fault may appear after a long journey or on a motorway, and not always straight away.
Symptoms
- Check engine light on, usually steady rather than flashing.
- Possible slight loss of power, especially under hard acceleration.
- A smell of sulphur or rotten eggs from the exhaust when the catalytic converter is saturated.
- Fuel consumption somewhat higher than usual.
- In some cases there are no visible symptoms and the code only appears during diagnosis.
- Slightly uneven idle if the mixture has been affected by leaks or degraded sensors.
Common causes
- Downstream lambda sensor slow, contaminated or with damaged wiring.
- Exhaust leak before the downstream sensor, letting in false air and altering the reading.
- Catalytic converter aged or degraded through mileage or prolonged use.
- Contamination of the catalytic converter by burnt oil, coolant or rich fuel.
- Unbalanced air-fuel mixture (too rich or too lean) overloading the catalytic converter.
- Repeated misfires sending unburnt fuel into the exhaust.
- Catalytic converter damaged by physical knocks or by overheating.
What to check
- Read the code with an OBD reader and also record the codes associated with lambda sensors and misfires.
- Visually inspect the exhaust for leaks, whistling or deteriorated gaskets, especially near the manifolds and sensors.
- Check the wiring and connectors of the downstream lambda sensor: moisture, corrosion, stripped wires or damaged insulation.
- Observe the live data from both sensors with the engine warm: the downstream one should remain relatively stable while the upstream one oscillates rapidly.
- Check for misfires (spark plugs, coils, injectors) by looking at the data for each cylinder.
- Analyse the short-term and long-term fuel trims to detect excessively rich or lean mixtures.
- Measure the exhaust back pressure with a suitable gauge to rule out an internal blockage of the catalytic converter.
- If all of the above is correct, replace the downstream sensor as a test before changing the catalytic converter, which is the most expensive part.
Common diagnostic mistakes
- Replacing the catalytic converter without first checking the downstream lambda sensor, which is a common and much cheaper cause.
- Ignoring small exhaust leaks that let in air and distort the sensor reading.
- Not checking for misfires, which may be the real cause of the catalytic converter's deterioration.
- Clearing the code and considering the problem solved without checking the underlying cause.
- Interpreting the sensor readings without the engine at operating temperature.
Typical repairs
From the simplest and cheapest to the most expensive. Which one applies depends on the diagnosis.
- Repair exhaust leaks and replace faulty gaskets or clamps.
- Correct misfires by replacing worn spark plugs or coils.
- Replace the downstream lambda sensor if its response is slow or it is damaged.
- Repair the sensor's wiring or connectors when they show corrosion or damage.
- Correct the mixture problem (airflow sensor, upstream sensor, injectors or fuel pressure) that is overloading the catalytic converter.
- Replace the catalytic converter when its degradation or contamination is confirmed, as the final and most costly repair.
Frequently asked questions
Can I keep driving with P0422 showing?
Usually yes, because the code does not normally affect immediate safety. It is worth checking soon, as a degraded catalytic converter can worsen fuel consumption and, if it overheats, damage other components. If the light flashes or you notice a severe loss of power, reduce the engine load and take it to a garage as soon as possible.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
Related codes
- P0420 It is the same type of catalytic converter efficiency fault, but referring to bank 2 on V or boxer engines.
- P0141 Indicates a heater fault in the downstream lambda sensor, which can cause a false P0422.
- P0136 Points to an abnormal voltage in the downstream sensor circuit, which also affects the catalytic converter reading.
- P0171 Mixture too lean on bank 1, which can overload the catalytic converter and eventually lead to P0422.
- P0300 Random misfire, whose unburnt fuel combustion can damage the catalytic converter.
More codes: auxiliary emission controls
- P0402 · Excessive Exhaust Gas Recirculation (EGR) Flow
- P0405 · EGR Sensor A Circuit Low
- P0406 · EGR Sensor A Circuit High
- P0411 · Incorrect Flow Detected in Secondary Air Injection System
- P0420 · Catalyst system efficiency below threshold (bank 1)
- P0421 · catalyst inefficient
- P0430 · Catalyst System Efficiency Below Threshold (Bank 2)
- P0440 · Evaporative Emission Control System Malfunction