Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0300: Random/Multiple Cylinder Misfire Detected

Severity: high

Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

Indicates that the ECU (ECM/PCM) has detected failed combustion in several cylinders, without being able to identify a specific one. Detection relies mainly on variations in crankshaft speed, measured with the crankshaft position sensor and, on some systems, with the camshaft position sensor. When a cylinder does not burn properly, its expansion stroke does not deliver the expected push and crankshaft rotation fluctuates in a recognisable way. The ECU compares those fluctuations with normal patterns and, if they repeat above a threshold, stores this code. If the misfire is serious enough to damage the catalytic converter, the warning light may flash.

Can I keep driving?

Only as far as you need to, and gently.

This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0300? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Noticeable jerking or shuddering, especially when accelerating or going uphill.
  • Rough idle or engine vibration when stationary.
  • Loss of power and slow throttle response.
  • Higher fuel consumption than usual.
  • Smell of unburnt petrol or rotten eggs from the exhaust.
  • Hard starting or an engine that stalls at idle.
  • Warning light on constantly or flashing on the instrument cluster.

Common causes

  • Worn, dirty or incorrectly gapped spark plugs.
  • Faulty ignition leads or coils, or individual coils failing.
  • Blocked, leaking or electrically faulty injectors.
  • Vacuum leak in the intake, for example in hoses or manifold gaskets.
  • Poor fuel quality or water contamination.
  • Low fuel pressure from a worn pump or filter.
  • Insufficient compression from worn piston rings, valves or head gasket.
  • Crankshaft or camshaft sensor with an irregular signal, or a wiring fault.
  • ECU or software fault, an uncommon cause.
  • The specific components and their order of checking depend on the manufacturer and model.

What to check

  • Check the warning light: if it flashes, reduce load and stop the vehicle as soon as possible. A flashing light indicates a serious fault that can damage the catalytic converter; do not keep driving with heavy jerking.
  • Read other stored codes. Codes P0301 to P0312 indicate a specific cylinder; also check for sensor or intake faults, and fuel mixture codes (P0171, P0174) pointing to an air leak or fuel problem.
  • Visually inspect spark plugs, leads and coil connectors, looking for moisture, cracks or burn marks. WARNING: the ignition system generates high voltage (tens of thousands of volts), capable of causing serious electric shock. With the engine off, switch off the ignition and do not touch leads or coils with the engine running.
  • Check vacuum hoses and the intake manifold for audible or smoke-detectable leaks. Work with the engine off or at idle with caution, keeping hands away from fans and belts.
  • Check the fuel level and quality; rule out water in the tank.
  • Measure fuel pressure with a gauge following the manufacturer's procedure. WARNING: the fuel circuit is pressurised and petrol is flammable. Depressurise before disconnecting parts, work in a ventilated area, with no flames, sparks or smoking, and keep a fire extinguisher to hand.
  • Check spark and injector pulse for each cylinder with an oscilloscope or suitable tester. This requires experience and specific equipment; if you are not confident, leave it to a professional garage.
  • Carry out a compression or leak-down test per cylinder if the other checks do not clarify the fault. Do it with the engine warm and spark plugs removed, with the ignition system disconnected for safety.
  • Check the signal from the crankshaft and camshaft sensors with an oscilloscope, comparing with the manufacturer's reference values. Consult the vehicle manual for values and test points.
  • As a last resort only, consider the ECU, after ruling out everything else. ECU replacement or reprogramming must be carried out by a professional.
  • If at any point you are not confident or do not have the right equipment, take the vehicle to a garage or qualified technician.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: ignition system and misfires

All OBD codes in English