P0303: Cylinder 3 misfire detected
Severity: high
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
Code P0303 means the ECU has detected incomplete or absent combustion in cylinder number 3 of the engine. Detection is based mainly on variation in crankshaft rotational speed: when a cylinder fails to deliver its power stroke, rotation over that part of the cycle drops noticeably, and the ECU interprets this as a misfire. On many engines the crankshaft position sensor signal is also used. Depending on the engine, the ECU may also rely on the lambda sensor signal and other sensors to interpret the fault. If the fault keeps recurring, unburnt fuel can reach the catalytic converter and damage it through overheating.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0303? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Jerking or juddering when accelerating.
- Rough idle, or the engine vibrating more than usual when stationary.
- Loss of power, especially on hills or when overtaking.
- Increased fuel consumption.
- A smell of unburnt petrol or exhaust fumes stronger than usual.
- Warning light flashing: this indicates a severe misfire that can damage the catalytic converter within a short time. Reduce engine load and have it checked as soon as possible.
- Warning light steady: the misfire is detected but, at that moment, is not as serious. It still needs checking, because it may become severe.
Common causes
- Spark plug in cylinder 3 worn, dirty or with incorrect electrode gap. This is one of the most common causes.
- Ignition coil for cylinder 3 faulty. On engines with individual coils this is a frequent cause; on engines with dual or shared coils the problem may affect more than one cylinder.
- Injector for cylinder 3 blocked, leaking or electrically faulty.
- Air leak in the manifold or intake near that cylinder, which leans out the mixture.
- Loss of compression from valves, piston rings or cylinder head gasket. Less likely, but usually accompanied by oil consumption or smoke.
- Damaged wiring or connector between the ECU and the coil or injector for cylinder 3.
- Note: cylinder numbering, coil layout and injection type depend on each manufacturer and each engine. Always confirm the position of cylinder 3 in the vehicle documentation.
What to check
- Safety first: work with the engine off and cold, except in tests that require it running. The ignition circuit generates very high voltages (≈ tens of thousands of volts): do not touch coils, leads or spark plugs with the engine running. If you lack experience or suitable tools, leave these checks to a professional.
- Check whether the warning light is flashing or steady. If flashing, reduce load and check as soon as possible.
- Read the code with an OBD-II reader, clear it and see whether it returns. Also check for other misfire codes (P0300, P0301, P0302) that point to a general problem.
- Review live data or the misfire counter per cylinder, if the reader allows it.
- Visually inspect the wiring and connectors of the coil and injector for cylinder 3, looking for moisture, damaged insulation or corroded pins, with the engine off.
- Remove the spark plug from cylinder 3 with the engine cold and check its condition: worn electrodes, carbon deposits, oil or moisture, and gap against the manufacturer's value.
- Swap the coil from cylinder 3 with that of another cylinder, with the engine off. If the code moves to that cylinder, the coil is the cause.
- Injector test: this is normally done with the engine running, which carries risks of burns, moving parts and fuel. With the engine off, measure its resistance. Flow and operation checks with a stethoscope are best left to a professional.
- Look for vacuum leaks with a dedicated smoke generator. If you use a spray, it should be non-flammable: brake cleaner is highly flammable and must not be used near a hot manifold or sparks. Without suitable equipment, use a professional.
- Measure cylinder 3 compression with the engine cold and, if necessary, carry out a cylinder leak-down test to locate losses from valves or piston rings. This usually requires a garage.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: ignition system and misfires
- P0300 · Random/Multiple Cylinder Misfire Detected
- P0301 · Cylinder 1 misfire detected
- P0302 · Cylinder 2 misfire detected
- P0304 · Cylinder 4 misfire detected
- P0305 · Misfire detected in cylinder 5
- P0306 · Cylinder 6 misfire detected
- P0307 · Cylinder 7 misfire detected
- P0308 · Cylinder 8 misfire detected