P0304: Cylinder 4 misfire detected
Severity: high
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code means the ECU has detected incomplete or absent combustion in cylinder number 4, according to the manufacturer's cylinder numbering. It detects this by monitoring variations in crankshaft rotational speed: when a cylinder fails to deliver its torque, the rotational speed in that section drops noticeably. If the fault repeats over several cycles, the ECU lights the warning lamp and stores the code. It can appear intermittently or constantly. On many vehicles, if the lamp flashes, this indicates a severe fault, with a risk that unburnt petrol will damage the catalytic converter. In that case, it is advisable to reduce the load and take the car to a garage as soon as possible.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0304? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Jerking or loss of power when accelerating, more noticeable on hills or when the engine is under load.
- Rough idle, with vibrations or running that feels "stuttery".
- Engine stalling when stopping, especially when cold.
- Engine warning lamp on, steady or flashing.
- Smell of unburnt petrol or higher fuel consumption.
- Harder starting than usual.
Common causes
- Ignition coil or spark plug on cylinder 4 faulty or worn. On engines with one coil per cylinder, this is one of the most frequent causes; on other designs the cause may vary.
- Cable or connector of the cylinder 4 coil with moisture, corrosion or poor contact.
- Cylinder 4 injector blocked, leaking or with an electrical fault.
- Compression leak in cylinder 4 due to valves, head gasket or worn piston rings.
- Unmetered air entering through a leak in the manifold or in a hose near that cylinder.
- General mixture problem (poor-quality fuel, dirty air filter or dirty air flow sensor) affecting all cylinders, although it is detected on one.
- Faulty crankshaft position sensor, which can generate false fault readings (less common).
- Fault in the wiring or in the injector or coil control unit, less common.
- Engine design: the layout of coils and injectors varies by make and model, so the exact part to check depends on each engine.
What to check
- If the lamp flashes, do not keep driving except to reach the garage, with low load and without high revs, as it may damage the catalytic converter.
- With the engine off and cold, visually inspect the connectors, cables and coils of cylinder 4 for moisture, oil or damage. High-voltage components can give electric shocks: do not touch the terminals with the engine running or with the ignition on. If you have no experience, leave this check to a professional.
- With the engine cold, check the cylinder 4 spark plug and compare it with the others: deposits, moisture, worn electrodes or incorrect gap. Remove it carefully so as not to damage the thread in the cylinder head.
- With the engine off, swap the cylinder 4 coil with that of another cylinder, clear the code and repeat the test. If the fault moves to the other cylinder, the coil is the cause.
- Check the air filter and intake hoses for leaks.
- Carry out a compression test or compression leak-down test on cylinder 4. This requires specific tools and is a garage task.
- Measure the flow or operation of the cylinder 4 injector only with suitable equipment or at a garage. The fuel system is under pressure and is a fire risk: do not work near sparks or heat sources, and do not smoke.
- Check live data (fuel trims, lambda sensor and per-cylinder misfire counters) with a scanner to confirm the cause.
- If the fault persists after the above, consider a professional diagnosis of the electrical system and the control unit.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: ignition system and misfires
- P0300 · Random/Multiple Cylinder Misfire Detected
- P0301 · Cylinder 1 misfire detected
- P0302 · Cylinder 2 misfire detected
- P0303 · Cylinder 3 misfire detected
- P0305 · Misfire detected in cylinder 5
- P0306 · Cylinder 6 misfire detected
- P0307 · Cylinder 7 misfire detected
- P0308 · Cylinder 8 misfire detected