P0307: Cylinder 7 misfire detected
Severity: high
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the ECU has detected incomplete or absent combustion in cylinder 7, according to the manufacturer's cylinder numbering. It detects this by observing small variations in the crankshaft's rotational speed, because a cylinder that does not fire stops contributing its torque and rotation becomes irregular at that instant. If the fault repeats over several driving cycles, the ECU confirms the error, lights the warning lamp and stores the code. If the lamp flashes, the fault is serious: unburnt fuel can damage the catalytic converter in a short time. In that case, it is advisable to reduce engine load and have the vehicle checked as soon as possible, without continuing to drive for extended periods.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0307? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Jerking or shaking when accelerating, especially uphill or under load.
- Rough idle or vibrations noticeable in the cabin.
- Loss of power and slower engine response.
- Increased fuel consumption.
- Smell of unburnt petrol or fuel from the exhaust.
- Warning lamp steady or flashing on the instrument cluster.
- In some cases, the engine stalls or starts badly when cold.
Common causes
- Worn spark plug, with incorrect electrode gap, dirty or wet.
- Faulty ignition coil. In engines with an individual coil per cylinder, this is one of the most frequent causes.
- Blocked, leaking or electrically faulty injector.
- Insufficient fuel pressure (pump, filter or regulator), which mainly affects the mixture of the cylinders.
- Loss of compression from burnt or poorly seated valves, worn piston rings or a damaged head gasket.
- Air leak in the intake next to that cylinder, which alters the mixture.
- Damaged wiring or connector, with poor earth or intermittent supply to the coil or injector.
- In engines with dual coils (one coil for two cylinders, with wasted spark), a coil fault affects two paired cylinders. If the code appears only on cylinder 7, it is usual to check the spark plug or injector of that cylinder first, although this is not a fixed rule.
- The layout of coils and spark plugs and the cylinder numbering vary by make and engine. Consult the manufacturer's manual.
What to check
- Safety: work with the engine off and cold. Ignition coils and leads carry high voltage (several thousand volts), so do not touch them with the engine running. If you need to measure fuel pressure, depressurise the circuit first and avoid sparks or flames nearby. If you have no experience with this work, leave it to a professional.
- Read all stored codes and freeze frame data to see whether there are other ignition or mixture faults.
- Visually inspect the spark plug of cylinder 7: colour, moisture, deposits and electrode condition.
- Check the condition of that cylinder's coil and its connector, looking for moisture, cracks or corroded pins.
- Swap the coil or spark plug with another cylinder and read the code again: if the fault moves, the part is defective.
- Measure the primary and secondary resistance of the coil against the manufacturer's values.
- Check the operation of the cylinder 7 injector (pulse with oscilloscope or current test) and its cleanliness.
- Measure fuel pressure at the rail, if the manufacturer specifies it.
- Check for vacuum leaks in manifolds, hoses and intake gaskets using smoke or spray.
- Carry out a compression or cylinder leakage test to rule out valves, piston rings or head gasket.
- Analyse live short-term and long-term fuel trim data to detect lean or rich mixture.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: ignition system and misfires
- P0300 · Random/Multiple Cylinder Misfire Detected
- P0301 · Cylinder 1 misfire detected
- P0302 · Cylinder 2 misfire detected
- P0303 · Cylinder 3 misfire detected
- P0304 · Cylinder 4 misfire detected
- P0305 · Misfire detected in cylinder 5
- P0306 · Cylinder 6 misfire detected
- P0308 · Cylinder 8 misfire detected