P0305: Misfire detected in cylinder 5
Severity: high
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the ECU (PCM) has detected that cylinder 5 is not burning the fuel correctly. To detect it, the ECU monitors variations in crankshaft speed between firing events, since a cylinder that does not burn stops contributing torque and rotation becomes irregular. If the irregularity exceeds the threshold set by the manufacturer, the code is stored and, in certain cases, the warning light comes on or flashes. A misfire is not limited to a loss of power: unburnt fuel can reach the catalytic converter and damage it, so it is advisable to identify the cause as soon as possible.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0305? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Jerking or vibration when driving, especially when accelerating or at idle.
- Noticeable loss of power.
- Rough idle or engine stalling at stops.
- Fuel consumption slightly higher than usual.
- Stronger smell of petrol or exhaust fumes.
- Warning light on steadily or flashing.
- In some cases, harder starting.
Common causes
- Spark plug in cylinder 5 worn, dirty or with incorrect electrode gap.
- Ignition coil for cylinder 5 faulty (on engines with individual coils or a coil pack).
- Injector for cylinder 5 blocked, leaking or electrically faulty.
- Low compression in cylinder 5 due to worn piston rings, poorly seated valves or a damaged cylinder head gasket.
- Vacuum leak located near cylinder 5 (manifold, gasket or hose).
- Damaged wiring or connector in the coil or injector circuit for cylinder 5.
- General fuel problems (low pressure or poor quality) are unlikely as an isolated cause: they usually affect several cylinders and produce P0300. If only cylinder 5 fails, these are ruled out.
- Note: the order of probability varies with engine design (individual coil, coil pack, direct or indirect injection), and the exact procedure depends on the manufacturer.
What to check
- Safety: switch off the engine and let it cool before touching injectors, manifold or wiring. Do not touch coils or spark plug leads with the engine running, as there is high voltage. Work in a ventilated area and away from flames or sparks. Tests on the fuel system (pressure, injectors) and the compression test require knowledge and suitable tools; if you do not have them, it is better to go to a garage.
- Check the condition of the spark plug caps and the appearance of the cylinder 5 spark plug (colour, moisture, deposits, electrodes).
- Visually inspect the connector and wiring of the coil and the injector for cylinder 5, looking for damage, moisture or corrosion.
- Swap the coil from cylinder 5 with that of another cylinder, clear the code and repeat the test: if the misfire moves to the other cylinder, the coil is the cause.
- Swap the spark plug with that of another cylinder to confirm whether the misfire follows it.
- Measure the resistance of the coil and injector against the manufacturer's values, using a multimeter.
- Check for vacuum leaks with diagnostic smoke or with a vacuum gauge on the manifold.
- Carry out a compression or cylinder leakdown test on cylinder 5, following the manufacturer's procedure.
- Analyse injector operation with an oscilloscope or with diagnostic equipment that shows the control signal.
- Review the ECU live data (misfire counter per cylinder, short- and long-term fuel trim) to confirm the pattern.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: ignition system and misfires
- P0300 · Random/Multiple Cylinder Misfire Detected
- P0301 · Cylinder 1 misfire detected
- P0302 · Cylinder 2 misfire detected
- P0303 · Cylinder 3 misfire detected
- P0304 · Cylinder 4 misfire detected
- P0306 · Cylinder 6 misfire detected
- P0307 · Cylinder 7 misfire detected
- P0308 · Cylinder 8 misfire detected