P0306: Cylinder 6 misfire detected
Severity: high
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the ECU has detected that combustion is not taking place correctly in cylinder 6 of the engine. To detect it, the control unit analyses variations in crankshaft speed, because each misfire causes a small momentary slowing of the rotation. If those variations exceed a threshold over a set number of revolutions, the ECU records the code and, according to regulations, may illuminate the warning light. A misfire means the fuel is not burning completely, so part of the mixture passes unburnt into the exhaust.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0306? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Engine stutter or jerking, especially when accelerating or at low revs.
- Rough idle or vibrations noticeable in the cabin.
- Loss of power and weak response when pressing the accelerator.
- Smell of unburnt fuel from the exhaust.
- Increased fuel consumption.
- Engine warning light on. If it flashes, the misfire is serious and should be treated as urgent: unburnt fuel can damage the catalytic converter. Reduce engine load and take the car to a garage as soon as possible.
Common causes
- Spark plug in cylinder 6 worn, dirty or with incorrect electrode gap.
- Ignition coil for cylinder 6 faulty. On engines with one coil per cylinder this is a common cause, although it depends on the engine design.
- Injector for cylinder 6 blocked, leaking or working irregularly.
- Air leak in the intake manifold or at the cylinder 6 gasket, which upsets the mixture.
- Low compression in cylinder 6 due to worn rings, valves or head gasket.
- Damaged wiring or connector in the coil or injector circuit for cylinder 6.
- Insufficient fuel pressure. It affects all cylinders, so it normally causes misfires on several at once; if it only appears on cylinder 6, it usually points to another cause.
The relative frequency of each cause depends on the engine design and the make (for example, whether the coil is individual or shared, or whether the injector is direct or port). Consult the manufacturer's documentation.
What to check
- Read the full codes with a scanner and check whether other misfire codes (P0300 to P0308) or mixture codes (P0171, P0174) appear that point to the cause.
- Before touching coils, plugs, leads or injectors, switch the engine off, remove the key and let it cool. Coils and ignition leads generate high voltage, which can be dangerous. If you have no experience, leave these checks to a professional.
- Visually inspect the coil, connector and wiring for cylinder 6, looking for moisture, cracks or loose connectors.
- Swap the cylinder 6 coil with that of another cylinder, with the engine off, and clear the code. If the fault moves to the other cylinder, the coil is the cause.
- Check the condition of the cylinder 6 spark plug and replace it if it is worn or dirty. Plugs from the same set should be changed together.
- Check the resistance of the coil and injector with a multimeter, following the manufacturer's values.
- Test injector operation with an oscilloscope or injector tester, or check its flow if blockage is suspected.
- If you are going to measure fuel pressure, first depressurise the circuit following the manufacturer's procedure. Petrol is flammable: do not work near flames, sparks or hot surfaces.
- Look for vacuum leaks using smoke, which is the safest method. Spraying liquid on the joints should only be done with non-flammable liquid and away from the exhaust and hot manifold.
- Carry out a cylinder compression or leak-down test to rule out internal mechanical damage.
- As a last step, if the above tests are normal, inspect the cylinder head and timing. These repairs should be assessed and carried out by a garage.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: ignition system and misfires
- P0300 · Random/Multiple Cylinder Misfire Detected
- P0301 · Cylinder 1 misfire detected
- P0302 · Cylinder 2 misfire detected
- P0303 · Cylinder 3 misfire detected
- P0304 · Cylinder 4 misfire detected
- P0305 · Misfire detected in cylinder 5
- P0307 · Cylinder 7 misfire detected
- P0308 · Cylinder 8 misfire detected