P0308: Cylinder 8 misfire detected
Severity: high
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the ECU has detected incomplete or absent combustion in cylinder 8. To detect it, the system monitors small variations in the crankshaft's speed, which occur when a cylinder does not deliver the expected force. If the irregularity repeats frequently, the code is stored. If the fault is serious, the warning light may flash. The code only applies to engines with 8 cylinders or more. Cylinder numbering depends on each manufacturer, so the actual position of cylinder 8 must be confirmed in the engine diagram.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0308? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Jerking or loss of power, especially when accelerating.
- Rough idle or vibrations with the engine running at idle.
- Flashing warning light: indicates a serious fault with a risk of damaging the catalytic converter. It is advisable to reduce engine load and have it checked as soon as possible.
- Smell of unburnt fuel or strong fumes from the exhaust.
- Harder starting or higher fuel consumption.
Common causes
- Worn spark plug or incorrect electrode gap.
- Faulty ignition coil on cylinder 8. On engines with one coil per cylinder it is one of the most frequent causes, although not always the only one.
- Injector blocked, leaking or with an electrical fault.
- Compression leak from burnt or misadjusted valves.
- Damaged or moisture-affected coil or injector cable or connector.
- Vacuum leak at the manifold or intake gasket that leans out the mixture.
- Fuel pressure problems or mass airflow sensor issues. These usually affect several cylinders, although they may be more noticeable in one.
- Serious mechanical damage (head gasket, piston rings), less likely but possible.
What to check
- Safety warning: before touching ignition coils, cables or connectors, switch off the engine and let it cool. The coils work at high voltage. If you need to handle the fuel system or injectors, keep away from flames and sparks. If you have no experience, leave these tests to a garage.
- Check whether the fault is intermittent or constant, and whether it appears only when cold or under load.
- Visually inspect the wiring, connectors and vacuum hoses near cylinder 8.
- Swap the cylinder 8 coil with that of another cylinder, clear the code and drive until a full drive cycle is completed. If the fault moves to the other cylinder, the coil is the cause.
- Check or replace the cylinder 8 spark plug, inspecting its condition and gap.
- Measure the resistance and operation of the cylinder 8 injector with a suitable tester, following the manufacturer's values.
- Carry out a compression or leak-down test on cylinder 8 to rule out mechanical problems. Do it with the engine cold and following the manufacturer's procedure.
- Read live data (fuel trim, lambda sensors, mass airflow sensor) to rule out causes affecting the whole engine.
- Check the fuel pressure and the condition of the intake system if the other checks are normal.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: ignition system and misfires
- P0300 · Random/Multiple Cylinder Misfire Detected
- P0301 · Cylinder 1 misfire detected
- P0302 · Cylinder 2 misfire detected
- P0303 · Cylinder 3 misfire detected
- P0304 · Cylinder 4 misfire detected
- P0305 · Misfire detected in cylinder 5
- P0306 · Cylinder 6 misfire detected
- P0307 · Cylinder 7 misfire detected