P0301: Cylinder 1 misfire detected
Severity: high
Updated: 13 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
This code indicates that the engine control unit (ECU/PCM) has detected that cylinder 1 is not burning the mixture correctly, that is, that a combustion misfire is occurring in that cylinder. To detect it, the ECU monitors variations in the crankshaft's rotational speed, because each correct combustion produces a small acceleration pulse and a misfire makes it disappear. When the irregularity repeats often enough, the code is recorded and, if the problem is severe, the warning light flashes to warn that unburnt fuel may damage the catalytic converter. The numbering of cylinder 1 depends on each engine's design and the manufacturer, so it is worth confirming in your vehicle's documentation exactly which one it is.
Can I keep driving?
Only as far as you need to, and gently.
This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0301? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Jerking or shuddering when accelerating or when cruising at a steady speed.
- Rough idle, with vibrations noticeable through the steering wheel or the bodywork.
- Loss of power and slower engine response.
- Difficult starting or an engine that struggles to settle when cold.
- Increased fuel consumption.
- Smell of unburnt fuel or stronger exhaust fumes. If the fuel smell is strong, pull over somewhere safe, switch the engine off and do not smoke or bring any flames near it.
- Warning light on the instrument cluster, either steady or flashing. If it flashes, it indicates a severe fault: do not keep driving unless essential, avoid hard acceleration and have the vehicle checked as soon as possible to avoid damaging the catalytic converter.
Common causes
- Cylinder 1 spark plug worn, dirty or with incorrect electrode gap.
- Cylinder 1 ignition coil faulty, especially if the vehicle has one coil per cylinder.
- Cylinder 1 fuel injector blocked, with irregular flow or an electrical fault.
- Loss of compression in cylinder 1 due to valves not seating, worn piston rings or a damaged head gasket.
- Damaged wiring or connector to the coil or injector, with corrosion or poor contact.
- Local air leak or false air intake near cylinder 1, which alters the mixture.
- Insufficient or irregular fuel pressure, although this usually affects more than one cylinder.
- Faulty sensors that alter the mixture or ignition, such as the crankshaft or camshaft position sensor, in less common cases.
- Serious mechanical damage, such as an internal engine failure, in rare cases.
What to check
- Safety before starting: work with the engine off and cold when touching spark plugs, injectors or coils. Ignition coils generate high voltage: do not touch or disconnect ignition components with the engine running. Before opening the fuel circuit, relieve the pressure following the manufacturer's procedure, and do not work near flames, sparks or while smoking. If you have no training on these systems, leave compression, fuel pressure and injector tests to a garage.
- Read the code with a scanner and check for other misfire (P0302, P0303, etc.) or mixture codes, which indicate whether the problem is common or local.
- Observe whether the warning light flashes and, if so, reduce load and avoid driving at full throttle.
- Visually inspect the wiring and connector of the cylinder 1 coil and injector for damage, moisture or corrosion, with the engine off.
- Remove and inspect the cylinder 1 spark plug with the engine cold: wear, deposits, moisture, damaged electrodes or incorrect gap.
- Swap the cylinder 1 coil with that of another cylinder only if the coil is accessible and the engine is off; clear the code, drive gently and check whether the fault moves to the cylinder where the coil is now. If it moves, the coil is the cause.
- Measure the resistance of the coil and injector with a multimeter, comparing with the manufacturer's values, with the component disconnected and the engine off.
- Listen to or check the operation of the cylinder 1 injector with a stethoscope or an activation test, or measure its flow if the garage has the equipment.
- Carry out a compression or leak-down test on cylinder 1 to rule out loss of sealing in valves, rings or head gasket. This is a garage test.
- Measure fuel pressure and check the condition of the filter and pump if the other cylinders also show problems. This is a garage test, due to the risk from pressurised fuel.
- Check for vacuum leaks in hoses and manifolds near cylinder 1, with the engine off or at idle and without placing your hand near hot parts or belts.
- As a last step, if all of the above is correct, analyse live data from the ECU and the crankshaft and camshaft sensors, or consider a more serious internal fault.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: ignition system and misfires
- P0300 · Random/Multiple Cylinder Misfire Detected
- P0302 · Cylinder 2 misfire detected
- P0303 · Cylinder 3 misfire detected
- P0304 · Cylinder 4 misfire detected
- P0305 · Misfire detected in cylinder 5
- P0306 · Cylinder 6 misfire detected
- P0307 · Cylinder 7 misfire detected
- P0308 · Cylinder 8 misfire detected