Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0440: Evaporative Emission Control System Malfunction

Severity: low

Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

Code P0440 means the ECU has detected a general fault in the EVAP system, the circuit that captures petrol vapours from the fuel tank and fuel system so they do not escape into the atmosphere. This system usually includes the tank, the cap, the vapour hoses, the charcoal canister and the purge valve. The ECU does not always know which component is failing, so the code points to an anomaly in the whole system. To detect it, the ECU applies pressure or vacuum to the circuit (depending on the system design) and checks whether it stays sealed. If it detects a leak or abnormal behaviour, it switches on the warning light. That is why the source of the problem can be as simple as a loose fuel cap or as complex as a blocked valve.

Can I keep driving?

Yes, it does not affect driving in the short term.

You can keep using the car normally, but do not ignore it: have it checked at your next service or if the warning light comes back after clearing it.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0440? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Warning light (check engine) lit steadily. If it flashes, the symptom does not match P0440 and the engine should be checked as soon as possible.
  • Smell of petrol, especially near the vehicle after refuelling or when parked.
  • On some vehicles, a whistling or hissing noise when the engine is running or just after switching it off.
  • Usually no loss of power or noticeable driving problems.
  • In some cases, the light goes off on its own after several driving cycles without a fault.

Common causes

  • Fuel tank cap not closed properly, damaged or with a worn seal.
  • Vapour hose cracked, loose or disconnected.
  • EVAP purge valve stuck open or closed.
  • Charcoal canister saturated or cracked.
  • Faulty ventilation or shut-off valve in the circuit (its presence and location depend on the make and model).
  • Faulty EVAP pressure or vacuum sensor (present only on some vehicles).
  • Corroded or loose electrical connector on a valve or sensor.

What to check

  • Before touching the fuel system, do not smoke, do not use flames or sparks, and work in a well-ventilated place. If there is a strong smell or visible fuel leaks, do not drive and take the vehicle to a garage.
  • Check that the fuel tank cap is properly closed and that its seal is not damaged or deformed. Replace it if worn.
  • Visually inspect the vapour hoses for cracks, breaks or disconnections, paying attention to areas near the tank.
  • Check the electrical connectors of the purge valve and the circuit sensors.
  • Read the EVAP system data and associated codes with a scanner, in case other codes appear that help guide the diagnosis.
  • Activate the purge valve with the scanner (actuation test) and check whether it responds.
  • Measure the resistance of the purge valve and compare it with the value specified by the manufacturer.
  • Carry out a smoke test on the EVAP circuit with specialist equipment, which can locate small leaks that are not visible to the eye. Do not introduce compressed air into the tank or overpressurise the system beyond what the manufacturer specifies, as this can damage components or cause dangerous leaks.

Frequently asked questions

Can I keep driving with the warning light on for P0440?

In general, yes, if the light is steady and there is no strong smell of petrol. The fault affects fuel vapour emissions and does not usually compromise safety or engine operation in the short term. It is advisable to check the system soon to avoid petrol smells and to stop the problem getting worse. If there is a strong smell of petrol, visible leaks or the light is flashing, this is not a typical P0440 case: stop driving and take the vehicle to a garage. If the light appears together with other engine faults, it is also better to take the vehicle to a garage.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: auxiliary emission controls

All OBD codes in English