Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0455: Large Leak Detected in Evaporative Emission Control System (EVAP)

Severity: low

Updated: 14 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

The EVAP system collects fuel vapours from the petrol tank and sends them to the engine to be burnt, rather than letting them escape into the atmosphere. The ECU monitors it through pressure or vacuum tests on the closed circuit, normally with the engine off and at a suitable temperature and fuel level. If it detects that the system is losing pressure faster than its large-leak threshold allows, it stores this code and usually lights the fault or check engine warning light. The exact threshold depends on the manufacturer, so the same leak may trigger the code on one car and not on another. It is an emissions fault, not an engine performance fault.

Can I keep driving?

Yes, it does not affect driving in the short term.

You can keep using the car normally, but do not ignore it: have it checked at your next service or if the warning light comes back after clearing it.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0455? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Fault or check engine warning light on, sometimes intermittent after refuelling.
  • Smell of petrol, especially near the tank or when parked.
  • Noticeable loss of performance: in most cases, none.
  • Normal idle or starting on most vehicles.
  • In rare cases, a slight increase in fuel consumption, difficult to notice in practice.

Common causes

  • Fuel cap loose, damaged, worn or with a deteriorated seal. This is usually the most common cause.
  • EVAP hose or pipe cracked, disconnected or loose.
  • Canister purge valve stuck in the open position.
  • Charcoal canister (canister) cracked or damaged.
  • Vent or system shut-off valve blocked or faulty.
  • Loose connections or a broken seal on the tank, filler pipe or fittings.
  • Faulty EVAP system pressure sensor, which can produce false readings.
  • Tank perforated or corroded, uncommon but possible on older vehicles.

What to check

  • Safety: work with the engine off, away from flames or sparks and without smoking. Do not open the fuel circuit or remove the tank without proper training. If there is a strong smell or petrol dripping, stop the inspection and go to a garage.
  • Check the fuel cap: that it is screwed on fully until it clicks, that the seal is not cracked or deformed, and replace it if necessary.
  • Check whether the code reappears after several driving cycles with the cap checked. The code disappearing on its own does not rule out a leak, because the ECU may detect it again in its next test.
  • Visually inspect the EVAP system hoses and pipes for cracks, breaks or loose connections, especially near the tank and the charcoal canister.
  • Check the electrical connections of the purge valve and the vent valve.
  • Carry out a smoke test on the EVAP system with specialist equipment, which locates leaks precisely.
  • Test the operation of the purge valve and vent valve with the scanner, observing their activation in live data.
  • Verify the reading of the EVAP system pressure sensor and inspect the charcoal canister if the other checks do not reveal the leak.
  • Check the condition of the tank for corrosion or perforations, especially on older vehicles.

Frequently asked questions

Why does code P0455 appear right after refuelling?

The most usual reason is that the cap is not closed properly or its seal is worn, so it lets vapours escape from the system. Refuelling changes the fuel level and the temperature of the tank, which can make the ECU detect the leak during its next tightness test. If the code returns after checking or replacing the cap, check the EVAP pipe, the purge valve and the charcoal canister, ideally with a smoke test.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: auxiliary emission controls

All OBD codes in English