P0446: EVAP Ventilation Control Circuit Malfunction
Severity: low
Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
The EVAP system collects petrol vapours from the fuel tank and the activated charcoal canister and sends them to the engine to be burnt, instead of letting them escape into the atmosphere. Within that system there is a ventilation valve which, depending on the design, opens or closes to allow a controlled entry of air. The ECU commands that valve and monitors that it responds to its orders through its electrical circuit. When the response does not match what is expected, or the circuit shows an open or a short circuit, P0446 is stored.
Can I keep driving?
Yes, it does not affect driving in the short term.
You can keep using the car normally, but do not ignore it: have it checked at your next service or if the warning light comes back after clearing it.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0446? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Malfunction indicator lamp (MIL) on, normally without any loss of power.
- Smell of petrol inside the cabin or around the vehicle, especially when refuelling.
- In some cases, slightly uneven idle or slightly higher fuel consumption, although this does not always appear.
- Often there are no noticeable symptoms during everyday driving.
Common causes
- Electrical connector on the valve loose, corroded or with damaged pins.
- Open or damaged wiring (chafing, deteriorated insulation, heat or animal damage).
- Ventilation valve stuck, faulty or with a defective winding.
- Fuel filler cap not closed properly or with a deteriorated seal, which can cause other related EVAP codes.
- Internal fault in the ECU or in the valve driver (uncommon).
- The location and type of valve vary according to make and model, so the exact point of failure must be confirmed with the manufacturer's documentation.
What to check
- Before touching the fuel system or the cap, work in a ventilated area, with no flames or smoking, and with the engine off and cold. If you need to disconnect components of the fuel circuit, first relieve the pressure following the manufacturer's procedure.
- Visually inspect the fuel cap: that it closes properly, that it has its seal in good condition and that it is not damaged.
- Inspect the connector of the ventilation valve: cleanliness, pins, clips and signs of moisture or corrosion. Do this with the ignition off.
- Visually inspect the accessible wiring for chafing, cuts or heat damage.
- With the ignition off and the valve connector disconnected, check the valve resistance and the continuity of the circuit with a multimeter, comparing them with the manufacturer's values. If the circuit is live or there are doubts about the voltage, leave the measurement to a professional.
- Use a scan tool to observe the live data of the valve and check whether it responds to the ECU's commands.
- Carry out a pressure or leak test of the EVAP system with a smoke machine, which makes it possible to locate leaks or blocked valves. This equipment must be used following the equipment manufacturer's instructions.
- Consult the make's technical bulletins, as some models have valves or connectors with known faults.
Frequently asked questions
Can I keep driving with the engine warning light on for P0446?
In general yes, because this code does not usually affect safety or the engine's mechanics, and the car usually runs normally. However, the lit warning light indicates that the vapour control system is not working correctly, which may prevent you from passing the emissions check or the periodic roadworthiness test (MOT in the UK), depending on the country. Do not drive if you notice a strong smell of petrol, if you see petrol leaks or if the problem comes with other faults. In that case, park outdoors, avoid sources of ignition and ask a professional for assistance. If there is only a slight smell, especially when refuelling, check the fuel tank cap and book a service so the fault does not go unattended.
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: auxiliary emission controls
- P0421 · catalyst inefficient
- P0422 · catalyst below efficiency
- P0430 · Catalyst System Efficiency Below Threshold (Bank 2)
- P0440 · Evaporative Emission Control System Malfunction
- P0442 · Small Evaporative Emission Control System Leak Detected
- P0450 · EVAP pressure sensor
- P0455 · Large Leak Detected in Evaporative Emission Control System (EVAP)
- P0456 · Evaporative Emission Control System Leak Detected (Small Leak)