Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0456: Evaporative Emission Control System Leak Detected (Small Leak)

Severity: low

Updated: 14 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code indicates that the ECU has detected a very small leak in the system that holds fuel vapours from the tank and directs them to the engine to be burned, instead of letting them escape into the atmosphere. The leak size considered significant is about ≈0.5 mm equivalent diameter, although the exact threshold depends on the manufacturer and the software version. To detect it, the ECU creates vacuum or pressure in the closed circuit, monitors how well it holds, and if the pressure drops faster than expected, it records the fault. That is why the system can warn even when there is no smell or visible fuel loss.

Can I keep driving?

Yes, it does not affect driving in the short term.

You can keep using the car normally, but do not ignore it: have it checked at your next service or if the warning light comes back after clearing it.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0456? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Malfunction indicator lamp (MIL) comes on in some vehicles, sometimes intermittently or only after several driving cycles; in others the fault is stored without the lamp lighting. It depends on the manufacturer.
  • In many cases there are no driving symptoms: the engine runs normally.
  • In some cases a slight smell of petrol may be noticed near the tank, especially after refuelling. A strong smell is not normal.

Common causes

  • Fuel cap loose, damaged or with a worn seal (this is often one of the most frequent causes).
  • EVAP hose cracked, softened or disconnected, especially near the tank or the activated carbon canister.
  • Purge valve that does not close fully.
  • Vent valve or canister shut valve that does not seal properly.
  • Connections or seals on the activated carbon canister with small leaks.
  • Damage from rubbing, rust or stones on the metal or plastic pipes running under the vehicle.
  • EVAP system pressure sensor giving an incorrect reading (less common).
  • The relative importance of each cause depends on the manufacturer and the system design; on some models the vent valve is a common failure, on others it is the hoses.

What to check

  • Check the fuel cap: that it is properly tightened (usually until it clicks) and that its seal is not cracked.
  • Visually inspect the EVAP hoses for cracks, breaks, deformations or loose connections.
  • Check whether there is a smell of fuel around the tank or the carbon canister.
  • Carry out a smoke test with specific equipment to locate the leak precisely (performed by a garage with the right equipment).
  • Use a scanner with bidirectional functions to activate the purge and vent valves and see whether they respond, if the vehicle allows it.
  • Measure the electrical resistance of the valves and compare it with the manufacturer's values.
  • Check the EVAP system pressure sensor and its electrical connections.
  • Repeat the leak test after each repair to confirm the system is sealed.
  • Safety warning: fuel vapours are flammable. Do not smoke, use flames or sparks, work with the engine hot, or handle fuel lines without the necessary knowledge. If there is liquid dripping or a strong smell, consult a professional.

Frequently asked questions

Can I keep driving with the warning light on because of this code?

In general yes, if the leak is very small and you do not notice a strong smell. This fault does not usually affect engine operation, the brakes or the airbag. What escapes are fuel vapours, which are flammable, so it is not wise to ignore it. If you notice a strong smell of petrol, see fuel dripping, or the cap is broken or does not close, do not drive and go to a garage. In other cases, check the cap and hoses when you can. Do not work on the fuel system yourself if you have no experience.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: auxiliary emission controls

All OBD codes in English