P0442: Small Evaporative Emission Control System Leak Detected
Severity: low
Updated: 14 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.
What it means
P0442 indicates that the ECU has detected a small leak in the system that holds fuel vapours from the tank before they reach the atmosphere. This system includes the tank, the charcoal canister, the purge and vent valves, and the hoses and seals that connect them. To check it, the ECU creates a slight vacuum in the circuit with the valves closed and monitors whether it holds; if pressure drops more than expected within a set time, it records the fault. It is a code from the evaporative emissions (EVAP) monitor, so its main effect is environmental and regulatory compliance, not mechanical.
Can I keep driving?
Yes, it does not affect driving in the short term.
You can keep using the car normally, but do not ignore it: have it checked at your next service or if the warning light comes back after clearing it.
If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.
Got P0442? Ask about your car
Tell us your car and what you notice: we answer right here, no account needed.
DATAIAO’s answer
AIYou are talking to an AI. It can make mistakes; it does not replace a professional. What we keep
Save this answer and your car, and I’ll ask you tomorrow whether it’s fixed.
Free and no card needed: 15 questions a day, your Garage and MOT/inspection reminders.
Warning: hazardous work
Affects:
Disclaimer. This information is for guidance only, is generated by artificial intelligence and may contain errors or omissions. Working on these systems can cause serious injury or death, as well as damage to the vehicle or to third parties. If you decide to do it, you do so at your own risk: always follow the manufacturer's workshop manual and the applicable regulations, and go to a workshop if you do not have the right training and tools. To the extent permitted by law, DATAIAO is not liable for damage arising from carrying out this work.
Symptoms
- Usually there are no symptoms while driving.
- A slight smell of petrol, especially when refuelling or after parking in the sun.
- Check engine light on, sometimes intermittent after several driving cycles.
- In some cases, the light switches itself off if the fault does not reappear over several cycles.
Common causes
- Fuel cap loose, damaged or with a worn seal (one of the most common causes).
- EVAP hose cracked, disconnected or softened by petrol or heat.
- Purge valve not closing properly or with an internal leak.
- Canister vent valve stuck open or leaking.
- Canister damaged or with loose connections.
- Fuel tank seal or connection leaking.
- EVAP system pressure sensor giving wrong readings (less common).
- The location and design of these parts depend greatly on the make and model, so it is worth consulting the EVAP system diagram for the specific vehicle.
What to check
- Check the fuel cap: that it tightens properly, that it clicks when tightened and that the seal is not cracked or damaged.
- Visually inspect the hoses near the tank and the canister, looking for cracks, chafing or disconnections.
- Listen with the engine off and after starting to see whether a hissing sound can be heard, and check for a smell of petrol in the area. If the smell is strong, do not continue with the tests and go to a garage.
- Check the purge and vent valve data with a scanner and run their actuation tests, if the equipment allows it.
- Carry out a smoke test on the EVAP system with a smoke generator, which is the most reliable method for locating the exact leak. Do it with the engine off, with no ignition sources (cigarettes, sparks, flames) nearby, in a well-ventilated place, following the manufacturer's procedure and pressure. Do not remove the fuel cap or tamper with the fuel circuit without the proper procedure. If you do not have the equipment or experience, have this test done by a professional.
- Check the canister and its lower connections, and the system pressure sensor, if the previous tests do not find the cause.
Frequently asked questions
Why can the car usually be driven normally if the P0442 code appears?
Because the EVAP system only controls fuel vapours and does not directly intervene in the engine or power output. A small leak does not noticeably alter the air-fuel mixture or how the engine runs, so the vehicle usually responds normally. However, the ECU records the fault and normally switches on the check engine light, so the car does warn of the problem even though there is no obvious loss of performance. It should be checked to prevent vapour emissions and the risk of failing the periodic roadworthiness test (MOT in the UK).
Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).
General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.
More codes: auxiliary emission controls
- P0421 · catalyst inefficient
- P0422 · catalyst below efficiency
- P0430 · Catalyst System Efficiency Below Threshold (Bank 2)
- P0440 · Evaporative Emission Control System Malfunction
- P0446 · EVAP Ventilation Control Circuit Malfunction
- P0450 · EVAP pressure sensor
- P0455 · Large Leak Detected in Evaporative Emission Control System (EVAP)
- P0456 · Evaporative Emission Control System Leak Detected (Small Leak)