Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0325: Knock Sensor 1 Circuit (Bank 1 or Single Sensor) Malfunction

Severity: medium

Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

The knock sensor is a piezoelectric element bolted to the engine block that picks up the vibrations characteristic of knock, that is, the uncontrolled combustion that occurs when the mixture explodes too early. The engine ECU receives the signal from this sensor and, if it detects knock, retards the ignition to protect the engine. The code is set when the ECU detects that the circuit for sensor 1, or for the single sensor on engines that only have one, is not delivering a valid signal: it may be open, short-circuited or at a voltage outside the expected range. While the fault persists, the ECU cannot monitor knock and usually applies a safety strategy with reduced ignition advance.

Can I keep driving?

Yes, but have it checked soon.

The car can normally be driven, but the fault can get worse or damage other parts over time (the catalytic converter or the particulate filter, for example). Book a diagnosis in the next few days.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0325? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • Check engine warning light on. With this fault the light may stay steady; flashing usually indicates another, more serious problem, such as a misfire.
  • Loss of power or weaker response, especially with the engine under load or during hard acceleration.
  • Rough idle or slight jerking, depending on the engine design.
  • Metallic knocking noise under load, if the ECU cannot correct it.
  • Higher fuel consumption due to the retarded ignition.
  • Some vehicles show no obvious symptoms and the fault is only detected when reading the fault codes.

Common causes

  • Damaged, broken or corroded wiring, or a loose connector between the sensor and the ECU. This is often one of the most common causes, although how frequent it is depends on the model.
  • Faulty knock sensor, due to internal wear or mechanical damage.
  • Sensor loose or incorrectly torqued, which alters the signal or causes false vibrations.
  • Poor cable shielding or earth, which introduces interference into the signal.
  • Internal fault in the ECU or its input stage, which is uncommon.
  • The exact location of the sensor, its type and the reference values depend on the manufacturer and the engine.

What to check

  • Visual inspection of the sensor connector and wiring, looking for stripped, crushed or burnt cables, or connectors with moisture or corrosion.
  • Check that the sensor is firmly secured to the block and that its tightening torque matches the figure in the manufacturer's manual.
  • Review the stored fault and the live data from the knock sensor, if the equipment allows it, to see whether the signal appears or is out of range.
  • Measure the sensor resistance with a multimeter and compare it with the manual value, as it varies by model.
  • Verify circuit continuity and that there are no short circuits to earth or to power between the sensor and the ECU.
  • Observe the sensor signal with an oscilloscope, tapping the block gently near the sensor to confirm it responds.
  • Swap the sensor with the one from the other bank, if the engine has two, to isolate whether the fault follows the sensor or stays in the circuit.
  • As a last resort, diagnose the ECU, after ruling out the sensor, wiring and mounting.

Frequently asked questions

Can I keep driving with code P0325 if the car runs normally?

Only if the car runs normally, with no loss of power and no knocking, can you keep driving with caution and avoid hard acceleration. Even so, it is worth having it checked soon: without a signal from the sensor, the ECU cannot detect knock and usually retards the ignition for safety, which reduces performance and increases fuel consumption. If you notice knocking under load, stop forcing the engine and take it to a garage as soon as possible, because sustained knock can damage it. The warning may be the only symptom, so do not ignore it.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: ignition system and misfires

All OBD codes in English