Create your free account and get 10 bonus questions when you confirm your email. No card needed. Create free account

Try it free

P0335: Crankshaft Position Sensor "A" Circuit Malfunction

Severity: high

Updated: 15 Nov 2026 · Generic OBD-II code (SAE J2012 / ISO 15031-6). Written with AI and reviewed; translated automatically from the Spanish original.

What it means

This code means that the engine control module (ECM/PCM) is not receiving a valid signal from the crankshaft position sensor, or that the signal received is not consistent with what is expected. The sensor reads the position and rotational speed of the crankshaft, usually from a toothed wheel or reference ring that passes in front of it. The ECM uses this information to calculate when to inject and when to fire each cylinder. If the signal is missing, intermittent or out of range, the ECM cannot synchronise the engine and logs the fault. That is why this code is important and should not be ignored.

Can I keep driving?

Only as far as you need to, and gently.

This fault can cause serious damage or affect safety. Avoid motorways, heavy loads and high revs, and have it diagnosed as soon as possible. If the engine shakes, loses power or a red light comes on, stop where it is safe.

If in doubt, put safety first: a red or flashing warning light, smoke, a burning smell or any change in the brakes or steering are reasons to stop.

Got P0335? Ask about your car

Tell us your car and what you notice: we answer right here, no account needed.

Symptoms

  • The engine stalls suddenly, especially while driving or when going over potholes.
  • Difficulty starting, or a start that only works on some attempts.
  • The start cuts out as soon as the engine tries to turn over by itself.
  • Rough running or jerking, with a loss of power.
  • Check engine warning light on, sometimes flashing.
  • On some vehicles, the rev counter does not work or shows erratic readings.

Common causes

  • Faulty crankshaft sensor, with an internal fault or wear.
  • Incorrect air gap or sensor out of position, due to faulty fitting or vibration.
  • Dirt or metal debris stuck to the tip of the sensor, attracted by the magnet.
  • Damaged toothed wheel or reference ring, with broken or worn teeth.
  • Damaged wiring, with chafing, cuts, poor joins or corroded or loose connectors.
  • Power supply or earth fault to the sensor.
  • Fault in the ECM, which is the least common cause. It should only be considered after ruling out the others.
  • Note: the sensor's location, its type (inductive, Hall effect or other) and its electrical specifications depend on each make and model.

What to check

  • Visual inspection: check the connector, the wiring near the sensor and its mounting. Look for heat damage, chafing or moisture.
  • Read additional codes and live data with a scanner. Check whether the engine speed signal appears steadily when the engine is cranked.
  • Inspect the tip of the sensor and the reference ring for metal filings, dirt or damaged teeth. This can be done by removing the sensor, provided it can be done safely. Work with the engine off and cold, and do not touch the toothed wheel or the wiring with the engine running. On hybrid or electric vehicles, first follow the manufacturer's high-voltage disconnection procedure; if you have no training for this, leave this check to a professional.
  • Check the power supply, earth and wiring continuity with a multimeter, according to the manufacturer's wiring diagram.
  • Measure the resistance of the sensor, if it is inductive, and compare it with the manufacturer's reference value. If it is Hall effect, check the supply voltage and the output signal.
  • Verify the air gap with feeler gauges, following the manufacturer's specification.
  • With an oscilloscope, observe the waveform of the signal with the engine running or while cranking. An irregular signal or one with gaps indicates a problem with the sensor, the wheel or the wiring.
  • Only if all of the above is correct, consider the ECM. Before replacing it, verify the ECM's power supply and earth.

Frequently asked questions

Can the car stop suddenly if the crankshaft sensor fails?

Yes. Without a reliable crankshaft signal, the ECM does not know the position of the engine or how fast it is turning, and it may cut the injection or the ignition. That is why the fault can cause a sudden stall, even while driving. If the engine stops on the road, the vehicle also loses brake servo assistance and, depending on the type of steering, power steering assistance, which makes braking and manoeuvring harder. If the warning light comes on, do not carry on driving normally until it has been checked. If the engine stalls or jerks, stop in a safe place and call for assistance.

Can I just clear it? Clearing the code does not fix the fault: if the cause is still there, it comes back, and with the engine warning light on the car will fail its roadworthiness test (MOT in the UK).

General information about a generic code. The exact causes depend on the make and engine: confirm them with a diagnosis before replacing parts.

More codes: ignition system and misfires

All OBD codes in English